Kenmore Dryer He3t Parts

The Tub Gasket is an OEM replacement part for Whirlpool washing machines. This gasket forms a crucial seal between the washer tub and the cabinet, both preventing water leaks and reducing noise and vibration. 

Causes of a bad tub gasket can include cracks, tears, or compression failures due to age, use, or impacts over time. Gaskets can also degrade with chemical exposure.

Symptoms of a bad tub gasket include:

• Water leaks from around the tub and cabinet interface 
• Excessive noise or vibration during spin and agitation cycles
• Reduced washer balance resulting in thumping or off-center loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

This electronic control board is the washer's central controller that directs cycle timing and power to key components. Replacing a failed board can restore proper starting, filling, spinning, and overall cycle completion.

• Coordinates wash, rinse, drain, and spin sequences based on sensor and user-interface inputs
• Switches power to the drive motor, water inlet valves, drain pump, and door lock
• Manages timing and relays to execute selected programs
• Common failure symptoms: won't start, won't advance or finish cycles, won't spin or fill/drain, intermittent operation, or fault/code displays

• Unplug the washer before servicing; electrical components can retain charge
• Use ESD protection and handle the board by its edges
• Photograph wiring and move connectors one at a time; transfer any brackets/covers from the original board
• Ensure all connectors are fully seated; after reassembly, run a diagnostic check per the service information

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

This replacement screw is a direct-fit fastening part used to secure panels and small components on compatible Whirlpool appliances. It restores proper fit and helps stop loose or rattling parts for reliable appliance operation. What it does:

• Secures trim, panels, or brackets to keep parts aligned and stable
• Prevents vibration-related noise caused by loose hardware
• Replaces missing or damaged screws that allow components to shift
• Restores factory fit where stripped or worn fasteners fail

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use the proper screwdriver or driver bit to avoid stripping the head
• Install carefully and tighten until snug; do not overtighten
• Keep track of small parts and fasteners during disassembly

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This pushbutton is the simple replacement button that restores tactile control and appearance to your appliance's front panel. It snaps into the control panel and provides the same push action as the original part. What it does:

• Replaces a broken, cracked, or missing pushbutton so controls respond properly
• Restores a stuck or intermittently working button to a solid, reliable push action
• Prevents dirt and debris from entering the switch opening when installed
• Improves panel appearance when the original is worn or discolored

• One pushbutton replacement

• Disconnect power to the appliance before beginning any repair
• Usually a snap-in installation; gently press into the panel until it clicks
• May require removal of the control panel or trim for access—keep fasteners organized
• If the switch beneath is damaged, replace the switch assembly rather than just the button