Kgs 907 Sss00 Parts

This is the 30-inch door panel for select ovens/ranges. It restores the door's appearance and provides the structural skin that supports the handle, glass, and trim for a solid, properly aligned door assembly. What it does:

• Forms the primary outer skin of the door assembly and supports handle/trim
• Provides a mounting surface for door glass and nameplate/emblems
• Helps maintain proper door alignment and a tight, rattle-free fit
• Common reasons to replace: dents, bends, scratches, discoloration, or stripped mounting holes

• 1 door panel

• Disconnect power and allow the appliance to cool completely before servicing
• Remove the door assembly and place it on a protected surface; wear cut-resistant gloves
• Transfer handle, screws, glass, and trim from the old panel to the new one; note screw lengths/locations
• Align carefully and avoid overtightening to prevent damaging threads or cracking glass

This fixed thermostat switches near 60C to control a heat-managed circuit—often the oven's cooling/blower fan. Replacing a failed unit restores proper fan cycling and helps protect the control area from excessive heat during and after cooking.

• Monitors temperature in the oven cabinet/control area and switches power based on heat level
• Cycles the cooling/blower fan on and off to manage cabinet temperature
• Helps safeguard electronic controls from heat buildup
• Failure may cause symptoms such as a fan that won't run, a fan that runs continuously, or an unusually hot control area

• Disconnect power at the breaker before servicing
• Access the thermostat per your model; it is typically mounted to a plenum or bracket near the oven cavity
• Move wires one at a time and mount the new thermostat flat against the surface for accurate sensing
• Restore power and verify the fan cycles during operation

This surface burner cap kit replaces worn or missing caps on gas cooktops and ranges. Properly seated caps shape the flame, protect burner heads from spills, and help restore fast, even ignition and consistent heating.

• Sits atop each burner head to focus the flame and shield the burner from spills
• Helps address hard-to-light burners, uneven or yellow flames, and lifting/noisy flames
• Replace if caps are chipped, warped, discolored, or missing
• Size- and position-specific—each cap must match its designated burner

• Turn off gas supply and power; allow the surface to cool completely before service
• Clean burner heads; align and seat each cap flat and centered with no wobble
• After installation, test each burner for a steady, even flame; reseat caps if ignition is delayed or flames are uneven

This 8-32 x 3/8 screw secures panels, brackets, and internal components in your appliance so everything stays aligned and tight. Replace worn or missing hardware to restore a solid, rattle-free fit and safe operation.

• Fastens components to frames, brackets, or panels
• Helps reduce vibration, rattling, and misalignment
• Replaces missing, stripped, or corroded screws
• Correct 8-32 machine thread for tapped holes in compatible assemblies

• Disconnect power before servicing; shut off gas or water if applicable
• Start threads by hand to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping

Color: Almond

This hex-head sheet metal screw secures appliance panels, brackets, and trim for a tight, rattle-free fit. Replace missing or stripped fasteners to keep covers and components firmly in place and restore proper alignment.

• Fastens sheet-metal parts, brackets, and trim using a hex drive
• Replaces worn, rusted, missing, or stripped screws
• Helps reduce vibration and rattling from loose panels
• Common signs you need this fastener: head or threads stripped, screw won't tighten, panel or handle coming loose

• Unplug the appliance before service; turn off water supply if working near water lines
• Use the correct nut driver or socket to avoid rounding the head
• Replace one fastener at a time to maintain alignment; do not overtighten
• Match screw type/length to the original location as specified by the manufacturer

Oven safety gas valve and regulator.

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This orifice holder serves the gas surface burner position designated TCB. It directs gas from the valve to the burner and provides a stable mount for the igniter and burner head to maintain reliable ignition and flame performance.

• Routes gas from the manifold/valve through the orifice to the burner head
• Supports proper alignment of the burner head and cap
• Provides mounting point for the surface igniter/electrode
• Failure symptoms include a burner that won't light or is slow to ignite, weak or uneven flame, or igniter clicking without ignition on that burner

• Disconnect power and shut off the gas supply before servicing
• Allow the cooktop/range to cool completely
• Remove burner cap and head; lift top as required. Transfer the brass orifice and igniter/electrode from the old holder if applicable, then install the new holder
• Reassemble, restore gas/power, and check all connections for leaks with a soap solution. Verify proper ignition and flame

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

This oven burner supplies the bake flame in a gas oven, restoring consistent heat for baking and roasting. Replace a damaged or corroded burner to help recover even cooking and reliable ignition. What it does:

• Produces the primary bake flame for the oven cavity so food cooks evenly.
• Replaces a warped, cracked, or heavily corroded burner that can cause weak or uneven heating.
• Can resolve symptoms such as the oven not reaching temperature, uneven baking, or a burner that won't light reliably.
• Works with the oven's ignition and gas flow system; proper flame appearance is important for safe operation.

• Turn off gas supply and electrical power to the appliance before beginning any service.
• Remove oven racks and access panels to reach the burner; retain all fasteners.
• Inspect and clean the burner ports and ignition area during replacement; avoid bending or damaging the burner ports.

This replacement screw secures appliance components and panels. Replacing worn or missing hardware restores a tight, rattle-free fit and helps keep assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or covers to the appliance frame or mating parts
• Helps maintain proper alignment and reduces vibration and noise
• Replaces missing, stripped, or corroded screws
• Common signs to replace: loose or rattling panels, misaligned parts, damaged screw head or threads

• Disconnect power; also shut off water or gas to the appliance if applicable
• Compare to the original to ensure thread and length match before installing
• Start threads by hand to avoid cross-threading; tighten only until snug
• If the mating clip/insert is stripped, replace that hardware as well

This fixed high-limit thermostat is a safety device for your oven. It monitors temperature and opens the circuit if the cavity overheats, helping protect components and restore normal heating when the failed thermostat is replaced.

• Provides over-temperature protection for the oven's heating circuit
• Opens the electrical circuit at a preset limit to stop heat when overheating occurs
• Typical symptoms of failure: oven won't heat, shuts off during use, or won't start after a self-clean cycle
• Often tests open for continuity at room temperature when failed

• Disconnect power at the breaker before servicing; oven circuits carry dangerous voltage
• Allow the appliance to cool completely before access
• Access location varies by model; the thermostat is typically mounted on or near the oven cavity or rear panel
• Move wires one at a time to the new thermostat, ensure tight spade connections, remount securely, restore power, and test

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.