Lfbd2409lmob Parts

Set of 8 screws and washers.

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

The Insulation is an OEM part for Frigidaire dishwashers. It is designed to reduce sound during wash cycles and help create a quieter dishwasher experience. The sound insulation minimizes noise transmission by absorbing and dampening vibrations throughout washing.

Causes of bad sound insulation can include breakdown of insulating materials over time, compression that reduces soundproofing density, or water damage or impacts.

Symptoms of bad sound insulation include:

• Noticeably louder operations with minimal sound dampening
• Rattling, banging, or buzzing sounds emanating from the appliance
• Transference of vibrations that causes adjacent cabinets to resonate

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This switch assembly is used in select dishwashers to provide a precise open/closed electrical signal to the control. Replacing a worn or sticking switch helps restore consistent cycle operation and reliable responses from the affected function. What it does:

• Sends an on/off (open/closed) signal to the control for the related mechanism in your model
• Helps ensure the connected function engages only at the correct time
• Common symptoms of a failed switch can include: cycle won't start, intermittent stopping, or improper filling/draining behavior
• A sticking or heat-damaged switch may cause erratic operation or error alerts

• One switch assembly

• Disconnect power (and water supply if required by access) before servicing
• Access location is model-specific; photograph wiring and note terminal positions before removal
• Transfer or reuse existing mounting hardware as applicable; ensure firm terminal connections
• After install, check switch actuation and run a test cycle to normal operation

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

Used on the upper rack track

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This console panel is the exterior fascia for the control area. It refreshes the appliance's appearance and provides proper support and alignment for the user interface components so the controls sit correctly and operate as intended.

• Forms the finished front of the control console in a black finish
• Supports and aligns the user interface/controls and related mounting hardware
• Helps shield internal controls from incidental contact at the front of the appliance
• Typical signs to replace: cracked or broken plastic, loose or missing tabs, misaligned controls, cosmetic wear or discoloration

• Disconnect power before servicing; wear cut-resistant gloves
• Photograph control layout and wire routing to aid reassembly
• Transfer existing screws, clips, handle trim, and user-interface parts to the new panel
• Ensure wiring isn't pinched and controls move freely before fully tightening fasteners

Replacement screw that secures trim, panels and internal components to restore proper fit and reduce rattling. Use when a fastener is missing, stripped, or corroded to help maintain stable, safe appliance operation. What it does:

• Secures panels, trim, brackets or other appliance parts to prevent looseness or movement.
• Replaces missing, worn, or damaged screws so components align and operate correctly.
• Helps reduce rattling, vibration noise, and gaps around doors or panels.
• Verify the exact size and thread before ordering to ensure proper fit.

• Disconnect power and water before starting any repair.
• Use the matching screw size and thread; do not force or overtighten.
• Start threads by hand to avoid cross-threading; use the correct screwdriver or bit.
• If threads or mounting holes are damaged, repair before reuse.

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit