Lgbd2431nfob Parts

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

This pulley is part of the dishwasher door balance system. It guides the door cable and spring so the door opens smoothly and stays controlled. A worn pulley can make the door feel heavy, drop open, or squeak.

• Routes the door balance cable between the hinge and spring to manage door tension
• Reduces friction for smooth, even door movement
• Helps prevent the door from slamming open or feeling excessively heavy
• Common symptoms: door drops or slams, won't hold a partially open position, squeaks or grinds near the base

• Disconnect power and turn off water supply before servicing
• Carefully relieve door spring tension; springs and cables are under load
• Pull the dishwasher forward to access the side frame area where the pulley mounts
• Note the cable routing before removal; install the new pulley and balanced door operation

Set of 8 screws and washers.

This pulley guides the dishwasher door's balance cable so the springs can counterweight the door. Replacing a worn or broken pulley restores smooth, controlled door movement and helps prevent the door from dropping or feeling heavy.

• Guides the door balance cable/cord to maintain proper spring tension
• Helps the door open and close smoothly and evenly
• Visible cracks, wobble, or flat spots on the wheel indicate replacement

• Disconnect power and shut off water before servicing
• Remove the toe-kick to access the side spring/cable area
• Support the door and carefully relieve spring tension; note the cable routing through the pulley
• Install the new pulley in the original position and inspect related cable/link and spring for wear

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

The Insulation is an OEM part for Frigidaire dishwashers. It is designed to reduce sound during wash cycles and help create a quieter dishwasher experience. The sound insulation minimizes noise transmission by absorbing and dampening vibrations throughout washing.

Causes of bad sound insulation can include breakdown of insulating materials over time, compression that reduces soundproofing density, or water damage or impacts.

Symptoms of bad sound insulation include:

• Noticeably louder operations with minimal sound dampening
• Rattling, banging, or buzzing sounds emanating from the appliance
• Transference of vibrations that causes adjacent cabinets to resonate

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

Restore your dishwasher's brains with this control assembly. It manages cycle selection and timing so the machine responds to commands, starts reliably, and completes wash cycles without random beeps, stalls, or unresponsive controls.

• Coordinates cycle logic and component operation
• Interprets button/touch inputs from the console
• Drives status indicators or display on applicable models
• Typical symptoms: controls unresponsive, won't start, lights flicker or beep erratically, cycle won't advance

• Disconnect power at the breaker before servicing
• Use anti-static precautions; handle the board by its edges and avoid touching contacts
• Label/photograph wiring; move connectors one at a time and fully seat any ribbon cables/locks
• Reuse existing mounting hardware; ensure correct orientation and secure harness routing before reassembly

This Main Wiring Harness is an OEM part for Frigidaire dishwashers. This harness transmits electrical signals to various components within the dishwasher.

Causes of a Bad Part: Wear and tear due to constant use, heat exposure, or moisture infiltration can cause the wiring harness to fray or short-circuit. Physical damage or manufacturing defects can also contribute to its malfunction.

Symptoms of a Bad Part:

• Inoperative dishwasher functions
• Electrical sparks or burning smell
• Visible damage or fraying on the wiring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball