Lmv1680 Parts

This canopy resistor regulates current to a range-hood or canopy fan circuit to help the blower run at the correct speeds. Replacing a failing resistor can restore proper fan speed control and stop intermittent operation. What it does:

• Controls electrical resistance in the canopy/blower circuit to help regulate fan speeds.
• Helps prevent the motor from running only on a single speed or from failing to start at selected speeds.
• Can cause symptoms such as inconsistent fan speeds, no response from speed controls, or occasional fan cutoff.
• Works with the hood's wiring and control switch to deliver the correct voltage to the fan motor.

• Disconnect power to the appliance before accessing the canopy or electrical connections.
• Inspect wiring and connectors for heat damage or corrosion; replace harness or terminals if damaged.

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This replacement mounting screw secures panels and small appliance components to restore proper fit and prevent vibration or loose parts. A simple, direct replacement when the original fastener is missing or damaged. What it does:

• Secures panels, brackets, or small assemblies to keep parts aligned
• Stops rattling or vibration caused by loose or missing screws
• Restores normal fit where a stripped or corroded screw failed
• Matches the OEM fastener form for a correct, long-lasting fit

• Unplug the appliance or disconnect power before servicing
• Use the correct driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or housing

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

The Interlock Door Switch is an OEM part for LG microwaves. It is a safety component located on the door of the microwave designed to prevent the microwave from operating unless the door is securely closed. The interlock door switch works with the microwave's electronic control board to sense when the door is open or closed and allow or disallow operation accordingly.

Causes of a bad interlock door switch can include normal wear and tear from repeated opening and closing of the microwave door over time.

Symptoms of a bad interlock door switch include:

• The microwave runs or heats with the door open
• Error codes or diagnostic messages related to door sensors on the control board
• The microwave fails to operate even when the door is securely closed

This OEM LG part is also compatible with some Sears/Kenmore microwaves.

Inner plastic door film covers the holes in the inner door frame.

This door frame assembly replaces the appliance's outer door trim and support to restore proper door fit and protect the inner door components. Ideal when the door frame is cracked, bent, or no longer secures the door evenly. What it does:

• Restores the outer door trim and structural support so the door closes and latches properly.
• Protects the door glass and inner components from impact and moisture intrusion.
• Helps eliminate gaps or misalignment that can cause rattling, air leaks, or difficulty closing the door.
• Matches the OEM form for a direct replacement when the original frame is damaged.

• Disconnect power and unplug the appliance before starting any repair.
• Remove the existing door trim/frame by loosening the retaining screws or clips; handle any glass carefully.
• Check door alignment and seal after installation; adjust hinge or strike as needed for proper fit.
• If the assembly has bonded or sealed components, consider replacing any associated gasket or fasteners if damaged.

This is a shelf, or warming rack, intended for use with microwaves. This shelf allows a place to set the items being warmed. With regular use, the shelf may get damaged. The shelf could also get misplaced. If there is a missing or broken shelf, the part should be replaced with a genuine OEM replacement part to continue the efficient performance of the appliance.Visual inspection of the shelf inside the microwave will quickly determine if the part is missing or broken. Replacing a damaged or misplaced shelf is a quick and straightforward process. Remove the old shelf and slide the new shelf into the proper position. Continue regular use of the appliance. Make sure that the metal shelf is not touching any part of the appliance on the inside, including the sides, top, or bottom.This shelf is an authentic OEM replacement part. It is made of high-quality, durable materials. The shelf is sourced directly from the manufacturer. This shelf for microwaves is compatible with several different models of appliances. It can be installed in many brands of microwaves, including devices produced by Kenmore, LG, Amana, and General Electric.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Size: 5 inches x 7 3/4 inches.