Lte6234dqo Parts

This rear foot assembly supports the back of the appliance and helps keep it level. Replacing a worn or missing foot restores stability, reduces vibration, and helps prevent the unit from rocking or "walking."

• Supports the rear of the cabinet and maintains proper height
• Provides a stable contact point with the floor for accurate leveling
• Helps reduce vibration, rattling, and movement during operation
• Common signs of failure: rocking/wobbling, excessive vibration, noise from the base, or a visibly worn/missing foot

• Disconnect power before servicing; if applicable, shut off water supply
• Protect the floor and carefully tilt or lay the appliance back with assistance
• Remove the old rear foot and install the new assembly per your model's instructions
• Set the unit back in place, level it, and verify stability

This replacement dispenser stores your dishwasher's detergent and rinse aid, then releases them at the proper time in the cycle. Restore consistent cleaning performance and help prevent leaks around the dispenser area with a fresh assembly. What it does

• Holds detergent and rinse aid; times their release during the wash cycle
• Seals to the inner door to help prevent leaks from the dispenser opening
• Common symptoms: detergent cup won't latch or open, detergent left after cycle, rinse aid not dispensing, leaking around the dispenser, broken latch/cover

• One dispenser assembly

• Disconnect power and water supply before servicing
• Open the door and remove the inner door panel to access the dispenser
• Transfer the wire connector(s); seat the gasket evenly and tighten mounting screws without overtightening
• Reassemble, restore power/water, and run a test cycle to check for proper operation and leaks

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

This agitator mover is the upper auger section of a dual-action agitator. It ratchets in one direction to drive clothes downward for proper turnover, helping restore effective wash action when the original mover is worn or damaged. What it does:

• Creates the one-way, ratcheting motion of the agitator's upper section
• Helps circulate and roll laundry downward for thorough turnover
• Common symptoms of failure: weak agitation, top auger not advancing, clicking/slipping sounds, or visible cracks/stripped splines
• Needed after damage from overloading or long-term wear

• 1 agitator mover (upper auger)

• Disconnect power and turn off water before servicing
• Remove the fabric softener dispenser and agitator cap; take out the center retainer/bolt to access the mover
• Lift off the old mover and seat the new mover fully on the agitator
• Reinstall the retainer/bolt and cap; verify smooth ratcheting action before use

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Size: 10-16 x 5/8 inch.

Vinyl door seal that forms an airtight barrier around the refrigerator or freezer door to help maintain proper temperature and reduce energy loss. Replaces worn gaskets to stop drafts and minimize frost or moisture build-up. What it does:

• Creates a secure, flexible seal around the door to help keep cold air in and warm air out.
• Helps prevent frost, condensation and uneven cooling inside the compartment.
• Commonly replaced when you see visible cracks, tears, gaps, or feel cold air leaking from the door edges.
• Can improve overall temperature consistency and reduce excessive compressor cycling caused by leaks.

• Remove the old gasket and clean the door frame thoroughly before installing the new seal.
• Warm water or a short exposure to gentle heat can soften a stiff gasket to make installation easier; handle carefully.
• Press the seal fully into the channel and check that it seats evenly around the entire door; avoid forcing or trimming unless specified by the OEM.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins/paddles to lift and move garments so water and detergent reach fabric fibers for better cleaning.
• Promotes even water circulation and load movement to reduce tangling and bunching.
• Common service reasons: cracked or broken fins, missing or worn agitator, noisy operation, excessive vibration, or clothes not coming out clean.
• Designed for top-load agitator-style wash systems that use the PC-144 agitator design.

• Disconnect power (unplug) and turn off water before starting any repairs.
• Typical replacement requires removing the existing agitator cap and any retaining hardware, then sliding the agitator off the drive post and installing the new unit; procedures vary by model—refer to your model's service manual or diagram.
• If a retaining bolt or special fastener is used on your model, have the correct socket or tool ready; follow manufacturer guidance for proper securing.

Almond. Size: 13 oz. can. Acrylic appliance paint.