Need Help?
Call or text
Fix excessive dryer vibration or motor movement with this motor isolator. Allows the motor to float properly on the floater plate for smooth operation.
Fix excessive washer vibration and loud rattling noises during spin with this rubber motor isolator mount. Cushions motor to reduce noise and wear.
Plastic retainer clip that secures the top cabinet panel to the washer chassis. Replace if cracked, broken, or missing to restore alignment and prevent rattling.
I replaced the fill valve assembly with a new one. Had to look carefully at the parts diagrams to make sure I ordered the right one since the serial number break old vs. new didn't seem to match the number on my machine. On this particular machine you don't need to pull it out too far from the wall-leave the hoses connected to the valve, remove the screw holding the valve bracket, and pull into the washing machine where you can easily access the hose ends. A putty knife is needed to open... Read more
10-24 x 0.50 inch hex head nickel screw for dryer assembly. Replace missing, stripped, or corroded screws that secure panels and components.
Replacement screw secures panels, brackets, and trim on washers and dryers. Replace missing, stripped, or damaged fasteners to restore proper fit.
Loose or vibrating parts? This threaded retaining locknut secures rotating components like shafts and pulleys. Simple DIY fix takes minutes with basic tools.
Stabilizer bracket secures internal components in your washer to reduce movement and vibration. Replace if cracked, broken, or missing to restore alignment.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
10-24 x 1/2 inch mounting screw for securing appliance panels, handles, brackets, and internal components. Replace lost, stripped, or damaged screws.
Machine screw fastens panels, brackets, and components inside appliances. Replace stripped, missing, or loose screws to restore secure assembly.
Fixes squealing or slow stopping at end of spin cycle. This spring maintains brake tension so the basket stops promptly. DIY repair takes about 1 hour.
I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more
Usually ships within 4 - 14 days
Washer won't spin or agitate? This lid switch assembly senses when the lid is closed, enabling spin cycles. Moderate DIY repair restores safe operation.
Replaced entire switch assembly Read more
Fix a loose or floating agitator with this mounting screw. Secures the agitator to the drive shaft to restore proper wash action. Easy DIY repair.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Washer won't start or stops mid-cycle? This lid switch housing secures the switch assembly for reliable lid detection. Simple DIY fix in minutes.
Seals the basket to center shaft, preventing leaks and reducing noise. Replace if leaking between tub and transmission. Confirm fit with your model.
Replaced all seals, unfortunately it is still leaking. I can see where it is leaking from. I am going to tear it back down use some ultra grey gasket maker and reinstall tub gasket. Hoping that works. If it still leaks I will be using the washer as a large paper weight. Read more
Replacement cabinet hinge for your dryer. Mounts the door panel to the cabinet frame. Order a new hinge if yours is cracked, bent, or broken.
Standard 8-18 x 3/8 inch mounting screw for securing panels, brackets, and components in appliances. Replace missing, stripped, or damaged screws.