Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix igniter sparking issues or non-responsive controls with this range rocker switch. Direct replacement part for common control panel failures.
Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Fix washer leaks and poor draining with a new tub-to-pump hose. Carries water from the outer tub to the drain pump. DIY repair takes just minutes.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
Usually ships within 4 - 14 days
Fixes squealing or slow stopping at end of spin cycle. This spring maintains brake tension so the basket stops promptly. DIY repair takes about 1 hour.
I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more
Filters debris and sediment from incoming water before it reaches the inlet valve. Replace if clogged or missing to restore proper fill flow. Confirm fit.
The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more
Replace your washer hinge bushing to restore smooth, quiet lid movement and proper alignment. Fixes squeaky or misaligned lids. Confirm fit with your model.
Replaced lid safety switch, actuator and plunger. Read more
Fix a loose or floating agitator with this mounting screw. Secures the agitator to the drive shaft to restore proper wash action. Easy DIY repair.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Seals the basket to center shaft, preventing leaks and reducing noise. Replace if leaking between tub and transmission. Confirm fit with your model.
Replaced all seals, unfortunately it is still leaking. I can see where it is leaking from. I am going to tear it back down use some ultra grey gasket maker and reinstall tub gasket. Hoping that works. If it still leaks I will be using the washer as a large paper weight. Read more
Mounting screw for dishwashers. Secures internal components and panels. Replace if stripped, missing, or corroded during repair or maintenance work.
Wire retainer secures wiring connections inside your dishwasher. Replace if the original retainer is cracked, broken, or missing to properly hold wires.
Fix a washer that won't fill with water or has temperature control issues. This temperature control board regulates water fill cycles in your washer.
Thrust bearing kit for washers. Installs on the motor plate assembly. Replace if broken, worn, or causing the motor plate to loosen during spin cycles.
Screws and instruction sheet included.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
First; The part was ordered on Thursday and I received it on Friday! The kit was the correct one and complete with everything needed. (Maytag Atlantis MAV6200AWW – APV4373103 tub seal kit & bearing) Great Service ! I will certainly recommend you guys ! Some of the things I encountered installing the tub-seal on a machine that is 15 years old: Be prepared to do considerable cleaning of the tub cover, tub assy and outer tub. The 4 tub assy bolts were very rusted to the point the ½ inch socket... Read more