Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Thrust bearing kit enables smooth transmission engagement in your washer. Replace if machine won't spin, makes grinding noise, or needs push-starting. Verify fit with your model number.
My Maytag washer make a loud screech when the washer tub needed to be stopped by the brake. Last year, I had replaced the suspension springs, the snubber ring, the drive belt and the drain pump. Those repairs worked fine, but a few weeks later, the screeching noise started. So I figured it was the brake system. I thought it would be better to replace the brake rotor and stator together as a set since I was going to disassemble both and they were 18 years old anyway. I decided to replace the... Read more
Snubber ring cushions the tub base during spin cycles. Replace if cracked, worn, or producing plastic shavings to restore smooth, quiet operation.
18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more
Washer making loud screeching or grinding noise during drain or spin? A failed drain pump bearing is the likely cause. DIY repair in 20-60 minutes.
It was a relatively easy fix. Removed the small access panel at the back of the washing machine after unplugging the unit. The pump is right there. Disconnected the two hoses to the pump, catching some water with towels. Removed three retaining screws, then realized I had not disconnected the belt from under the unit. Easy fix, tilted the unit and disconnected the belt. Put in the new pump , connected the hoses, then reconnected the belts. Works like new! Read more
Drive belt connects the motor to drum for wash and spin cycles. Replace if washer won't spin, makes noise, or smells like burning rubber. Confirm fit.
Washer won't spin, makes grinding noise, or has burning smell? Motor assembly drives drum rotation. DIY-friendly repair, typically 30-60 minutes.
I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more
Suspension spring that supports the washer tub and absorbs vibrations. Replace if broken, cracked, or stretched to restore proper tub support.
Secures washing machine hoses to prevent leaks in the water system. Replace if damaged, corroded, or connections are loose. Verify fit by part number.
We ordered parts from appliance parts pros and I fixed it. Read more
Replaces cracked, broken, or weakened motor spring that maintains proper tension between motor and floater plate in top-load washers. Direct fit part.
Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more
Fix a washer that won't stop filling or overflows with a new water inlet valve. Controls hot and cold water flow during fill cycles. 15-20 min repair.
Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Washer won't agitate or spin after opening the lid? A faulty lid cam prevents the switch from engaging. Easy 15-minute DIY fix restores operation.
I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more
Washer won't spin or stops mid-cycle? A faulty lid switch prevents operation when the lid is bumped or opened. Simple snap-in replacement restores cycles.
I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more
Fix a washer that won't start when the lid is closed with this lid switch plunger. Simple DIY repair—just remove two screws and realign. Video included.
Replace your dryer's broken, cracked, or missing timer knob. This control knob installs on the timer shaft to set drying cycles and time settings.
Replaced timer Read more
Rubber inlet hose that connects your washer to the water supply. Replace if cracked, leaking, or worn. Standard 5-foot length with included washers.
Replaced flow meter and control valve Read more
Replace your cracked or missing timer knob cap to restore control panel appearance. Simple 5-minute DIY fix. Chrome finish includes locking pin design.
Watched the video and in 5 mins I was all done, very easy. Read more