Maytag Cwe 4800 Parts

The Fresh Food Evaporator Cover with Deli Drawer Fan is an OEM part for GE refrigerators. Located inside the refrigerator compartment, this assembly helps properly circulate cool air throughout. 

Symptoms of a bad evaporator cover or deli fan include:  

• Warm or inconsistent temperatures within sections of the interior
• Frost or ice buildup in areas of poor air circulation
• Abnormal sounds from the fan such as grinding or squealing noises
• The fan fails to spin or rotate when the deli drawer is opened

Causes can be normal wear over time. Dust and debris accumulation may restrict airflow or cause imbalances. Infrequent cleaning allows contaminants to interfere with fan function.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This straight 1/4-inch water line coupler joins two sections of 1/4-inch OD refrigerator tubing, restoring a secure connection in dispenser and icemaker supply lines. Use it to splice, repair, or extend existing tubing.

• Creates an inline union for 1/4-inch OD refrigerator water tubing
• Helps address leaks, cracks, or breaks by replacing a damaged connector or splicing a cut line
• Useful when rerouting lines or adding inline components such as filters
• Common symptoms: water dripping at a tubing joint, loose/disconnected line, reduced or no water to dispenser/ice maker

• Unplug the refrigerator and turn off the water supply; dispense water to relieve pressure
• Cut tubing ends square and clean; ensure both tubes are 1/4-inch OD
• Make secure connections per the coupler design (push-to-connect or compression); ensure tubing is fully seated/assembled and gently pull to verify
• Restore water and check thoroughly for leaks

This terminal block is the insulated connection point where the appliance's incoming power ties into the internal wiring. Replacing a heat-damaged or loose block restores a safe, reliable electrical path and helps prevent arcing and intermittent power loss.

• Connects the supply conductors to the unit's internal wiring
• Provides insulated posts to securely fasten and distribute power
• Helps maintain tight, low-resistance connections
• Common failure signs: melted/discolored plastic, burned or loose terminals, arcing, scorching, or intermittent/no power after confirming the cord and breaker

• Disconnect power at the breaker or unplug the appliance; verify no voltage before servicing
• Photograph or label wire positions to ensure correct reassembly
• Inspect and replace any heat-damaged wire ends or lugs; use appropriate terminals
• Tighten connections securely and ensure wires are fully seated and strain-relieved as originally installed

This door hinge restores smooth, controlled opening and a tight seal on the oven door. It supports the door's weight with spring tension so the door closes fully and stays positioned without slamming or sagging.

• Provides the spring-loaded pivot that controls oven door movement
• Helps ensure the door closes flush for a proper seal and heat retention
• Common symptoms: door won't close fully, drops or slams, won't stay at a set angle
• Reduces squeaks/binding and corrects uneven gaps around the door

• Disconnect power to the range or wall oven; shut off gas supply if applicable
• Remove and support the door to access hinges
• Springs are under high tension—use caution and proper locking method; wear gloves and eye protection
• After installation, verify door alignment and gasket contact all around

The Screw is an OEM replacement part for Whirlpool ranges. This screw is used to secure various components of the range, ensuring that parts such as panels, brackets, or burners remain firmly in place during operation. It is designed to withstand the high-heat environment of a range, providing long-lasting durability.

Symptoms of a bad or missing Screw include:

• Loose or misaligned range components
• Rattling or unusual noises during operation
• Difficulty maintaining the range's structural stability

Causes of a failing or missing screw can include normal wear over time, accidental loss during maintenance or repairs, or damage from overtightening. Replacing faulty screws ensures the appliance remains safe and functional.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement thermostat knob mounts on the control shaft to set cooking temperature. It restores a secure grip and clear pointer so you can choose settings reliably when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the thermostat/control shaft to adjust temperature settings
• Provides a clear pointer and tactile grip for accurate selection
• Can help resolve issues like slipping, not engaging the stem, or worn/illegible markings
• Helps restore consistent temperature adjustment when the original knob is damaged or missing

• One thermostat control knob

• Turn the appliance off and allow surfaces to cool before servicing
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the new knob with the shaft orientation/indicator and press on until fully seated
• Verify the pointer aligns with the Off/temperature marks and turns smoothly through the range

The LED and Cover Assembly is an OEM part for GE refrigerators. This component illuminates the interior compartments and includes light-emitting diodes (LEDs) with a protective transparent cover. It provides enhanced visibility of stored items through energy-efficient white lighting.

Causes of failure can be related to the electronic operation of the LEDs themselves wearing out over the lifespan of many on/off cycles. The cover plastic may develop cracks or scratches from regular cleaning.  

Symptoms include:

• Dimming or flickering lights that no longer shine brightly
• Discoloration of the cover material obstructing light transmission
• Loose or detached cover that won’t stay securely fastened 

This GE OEM replacement restores clear illumination for stored items. With long-lasting LED technology behind a shatter-resistant shield, it ensures dependable visibility during nighttime fridge access. Compatible with later produced Hotpoint, RCA, and Kenmore refrigeration models as well.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.

• Provides the pivot and spring action at the door's upper mounting point
• Maintains door alignment for proper gasket contact and heat seal
• Typical symptoms of a failing hinge: door won't close fully, sags, binds/rubs, or pops open
• A poor seal from a worn hinge can lead to heat loss and uneven baking

• Disconnect power and allow the oven to cool completely before service
• Support the door; many models require removing the door to access the hinge
• Install at the factory mounting points and ensure the hinge fully engages the receiver
• After replacement, check door alignment and that the seal contacts evenly

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fastens sheet-metal panels, brackets, and small components in the appliance cabinet
• Replaces lost, stripped, or corroded screws to maintain secure mounting
• Helps reduce vibration, buzzing, or rattling from loose parts
• Useful when the original hardware is missing or no longer holds securely

• Includes 1 screw-and-washer fastener (8-18 x 5/16)

• Disconnect power; shut off gas and water supplies if applicable
• Match the fastener to the original location; sizes can vary by application
• Start threads by hand to avoid cross-threading; use an appropriately sized driver
• Tighten snugly without overtightening to prevent stripping sheet metal

The Damper Assembly is an OEM component specifically designed for GE refrigerators. This assembly is located within the fresh food compartment and functions to control airflow and temperature regulation. 

The damper works with the evaporator fan to carefully moderate circulating air, preventing cold spots and optimizing equal cooling. Consistent temperatures extend the shelf life of perishable goods. 

Causes of a faulty damper assembly can include failure of the plastic gears or axle that coordinate its movements over time. Improper air circulation disrupts the refrigerator's performance.

Symptoms include: 

• Formation of frost or ice buildup in problem areas  
• Inconsistent shelf temperatures from top to bottom
• Foods spoiling more quickly 

This replacement assembly from GE restores dependable temperature control. Upgrade today for continued fresh food preservation abilities matching OEM standards. It is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Overload Ptcr Combo is an OEM part for GE refrigerators. It is responsible for regulating the electrical current flowing to the compressor. It helps prevent damage to the compressor and extends its lifespan.

A bad overload ptcr combo can be caused by power surges, electrical malfunctions, or normal wear and tear over time.

Symptoms of a bad overload ptcr combo include:

• The refrigerator not cooling properly.
• The compressor making unusual noises or not running at all.
• Excessive heat around the compressor area.
• Frequent tripping of the circuit breaker.

Replace your worn-out or damaged overload ptcr combo with this genuine OEM part and ensure the efficient and reliable operation of your refrigerator's compressor. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This Mullion Spring Sleeve is the small bushing that fits over the door mullion (center flipper) spring. It guides the pivot and reduces wear so the flap folds smoothly and helps maintain a tight seal between refrigerator doors.

• Provides a smooth bearing surface around the mullion spring/hinge pin for reliable pivoting
• Helps the mullion fold out on opening and spring back to close the center gap
• Wear or loss may present as a loose or binding flipper, clicking/grinding, or a gap that prevents a full seal
• Replacing the sleeve can help restore proper flipper action without replacing the entire mullion assembly

• Disconnect power and clear items from the door; remove the mullion from its top and bottom pivots, noting the spring orientation
• Slide off the worn sleeve from the spring/pin and install the new sleeve in the same position
• Reinstall the spring and mullion; verify the flipper opens/closes freely and the center seal makes full contact
• Wear cut-resistant gloves; edges around the door and hinge can be sharp

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

Size: 10-32 GXTT FLP.595 S