Maytag Dg7500 Parts

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This drum baffle mounts inside the rotating drum to lift and tumble laundry during each cycle. Replacing a cracked, loose, or missing fin helps prevent snags and restores proper load movement. What it does:

• Lifts and turns items as the drum rotates to improve tumbling
• Separates garments to reduce tangling and keep loads moving evenly
• Helps prevent small items from lying flat against the drum surface
• Common symptoms include rattling or thumping, visible cracks, clothes snagging/tearing, and reduced tumbling

• One tall drum baffle

• Disconnect power; shut off gas supply before servicing
• Wear cut-resistant gloves; interior cabinet edges can be sharp
• Rotate the drum to access mounting points; support the drum while removing/installing the baffle
• Tighten fasteners securely; hand-turn the drum to verify clearance before testing

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Specs: No.8X1/2 HEX WASHER HEAD

This rotary timer controls cycle sequencing and run time for compatible Whirlpool appliances, restoring proper cycle advancement and timing when the original timer fails. Use it to replace a worn or non-responsive timer assembly and regain normal operation. What it does:

• Advances the appliance through wash/dry or cook cycles by switching power to motors, heaters and valves.
• Replaces failed timing/selection functions; common symptom is a unit that won't advance to the next cycle.
• Can cause intermittent or no operation of timed components when contacts wear or wiring fails.
• May stop a cycle prematurely or produce erratic timing if internal switch cams or contacts are damaged.

• Disconnect power (unplug or shut off breaker) before attempting any service.
• Access typically from the control panel — remove retaining screws and control knobs as needed.
• Note wire positions or take a photo before removing the harness; reinstall harness and shaft in original alignment.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

This door strike is the replacement latch striker that the door latch catches on to secure the appliance door. Restores proper door engagement and helps the door close and seal correctly. What it does

• Provides the matching contact point for the door latch so the door stays closed
• Commonly replaces worn or broken strikes that cause the door to not latch or to pop open
• Can resolve noisy closing, misalignment, or intermittent latching issues
• Works with the OEM latch assembly to maintain proper door alignment and sealing

• One door strike

• Disconnect power (or unplug) before starting any repair
• Remove exterior panels or trim as needed to access the strike; keep all fasteners
• Align the strike so the latch engages smoothly — do not force components

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.

• Secures panels, brackets, and internal components to the cabinet or frame
• Helps prevent vibration, rattling, and misalignment from loose hardware
• Replaces a missing, rusted, or stripped original screw
• Matches the original fastener style for proper fit in specified locations

• Disconnect power; shut off gas and water supplies before servicing
• Use the correct screwdriver or nut driver and match length/thread to the original
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic or thin metal

A single replacement screw used to secure panels and components on compatible Whirlpool appliances. This genuine-style fastener restores proper fit and keeps parts aligned for safe, reliable operation. What it does

• Secures panels, brackets, or small components to the appliance frame
• Restores proper alignment for doors, control panels, or internal assemblies
• Helps eliminate rattles, loose parts, and poor fits caused by missing or damaged screws
• Simple, direct replacement when the original screw is lost or stripped

• One replacement screw

• Use the matching screwdriver or bit and tighten only until snug; avoid over-torquing which can strip threads or crack plastic
• Replace with the same size and thread form; compare to the original before installing
• Disconnect power to the appliance before accessing internal components to reduce shock risk

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts