Maytag Mah550bww Parts

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

The Timer Knob is an OEM replacement part for Whirlpool dryers. It allows users to set cycle durations with smooth, intuitive adjustment.

Symptoms of a faulty timer knob include:  

• The timer knob does not turn or is difficult to turn.
• The timer knob is missing

Causes of a bad timer knob can include loose or stripped internal gears from an extended operation or impact damage during loading/unloading clothes. 

Note: This is the center portion of the knob only. For the complete knob assembly, the cap and skirt must also be purchased.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

Door lock hoop assembly that positions and secures the door latch striker so the door closes and the interlock can engage. Replacing a worn or damaged hoop restores proper door alignment and reliable door closure. What it does:

• Positions the latch striker so the door can fully engage and stay closed.
• Allows the door interlock to operate correctly; often replaced when the appliance won't start because the door won't latch.
• Reduces door play and rattling caused by a bent, cracked, or worn hoop.

• Disconnect power (and water supply for washers) before starting any repair.
• Access may require removing the door or front panel; follow the appliance service manual for model-specific steps.
• Inspect the latch/strike and mounting hardware while installing; replace any damaged components and verify correct alignment before reassembly.

This 1-1/4" washer is a replacement flat washer used to secure fasteners and distribute load for reliable appliance assembly. It helps maintain proper clamping and prevents bolt/nut damage for stable operation. What it does:

• Sits under a nut or bolt head to spread load and protect mating surfaces
• Prevents fastener loosening caused by vibration or movement
• Reduces wear between joined parts to extend component life
• Helps maintain correct alignment of assemblies where used

• Turn off and unplug the appliance before beginning any repair
• Match this washer to the original by size and thickness to ensure a proper fit
• Use appropriate hand tools and replace any corroded or damaged fasteners at the same time

Replacement timer that controls the appliance's cycle sequencing and timing so selected programs run and advance correctly. Restores predictable cycle changes and helps the appliance complete programmed operations. What it does:

• Regulates cycle timing and advances the unit through programmed stages
• Directs power to timer-controlled functions so motors, heating, or valves operate at the correct times
• Common symptom fixes: appliance stuck on one cycle, cycles won't advance, or inconsistent cycle behavior
• Works as the central sequencing component for timed functions and user-selected settings

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Replacement typically requires removing the control panel or console and detaching the timer from its connector(s)
• Handle electrical terminals and connectors carefully; avoid bending or damaging pins

Includes ball bearing, rear bearing, water deflector, hose clamp, spacer, motor isolator, plug & Lip Seal

This front baffle grommet cushions and secures a dryer's front baffle to reduce vibration and noise while helping keep the baffle properly positioned during operation. Fits select Whirlpool-built dryers. What it does:

• Cushions the baffle to reduce rattling, knocking or squeaking noises during spin
• Holds the baffle in place to prevent movement or rubbing against the drum
• Helps maintain even drum rotation and prevents premature wear of plastic/metal parts
• Can wear or crack with age, causing noise or loose baffle symptoms

• High-level replacement — remove dryer front or access panel;
• Use proper tools and support panels; keep screws and fasteners organized for reassembly
• Disconnect power (and gas if applicable) before starting work

This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:

• Replaces a damaged or bent door hinge to correct misaligned or sagging doors
• Restores smooth hinge movement for easier opening and closing
• Helps the door seal properly to maintain internal temperature and efficiency
• Prevents rubbing or binding that can damage door gasket or cabinet finish

• Disconnect power to the appliance before beginning any repairs to avoid injury
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow for correct alignment and torque
• After installation, check door alignment and gasket contact; adjust as needed

Spesc: #12 pozi - drive

This vent tube assembly directs exhaust airflow from the dryer to the cabinet exit, restoring proper venting and reducing moisture buildup. It's a direct-fit replacement that helps return your appliance to normal drying performance. What it does:

• Channels hot, moist air from the dryer drum to the exhaust outlet to prevent interior condensation.
• Replaces damaged, crushed, or disconnected tubing that can cause poor drying or longer cycle times.
• Helps reduce lint accumulation at the blower assembly by providing a continuous exhaust path.
• Can resolve symptoms like reduced drying efficiency, excess humidity around the appliance, and unusual airflow noises.

• One vent tube assembly

• Disconnect power (and gas supply if applicable) before starting any repair.
• Access the dryer rear or cabinet per your model's service instructions to remove the old tube and install the new one.
• Ensure the tube is routed without sharp bends or kinks and secure clamps/fasteners tightly to prevent leaks.