Maytag Mle 2000 Ayw Parts

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

The push-to-start switch activates the dryer motor when you press the Start button. Replacing it restores dependable starting with one press.

• Completes the start circuit to power the motor when pressed; spring-returns when released
• Restores normal operation when the original switch is worn, stuck, or electrically open
• Symptoms include: dryer won't start, starts only while button is held, intermittent starting, or no response when pressing Start
• Mounts in the control console behind the Start button/knob; connects with spade terminals

• Disconnect power to the dryer before servicing
• Remove the console/trim as needed to access the switch; pull off the knob if present
• Note wire positions (take a photo); move wires to the new switch one at a time and secure
• Test operation; also check the door switch, thermal fuse, and belt switch

Color: White

This machine control board is the washer's electronic brain, directing the motor, water valves, and cycle timing. Replacing a failed board restores proper control of wash, rinse, and spin functions and helps resolve erratic or non-starting cycles.

• Coordinates cycle timing and sends power to the drive motor, drain pump, and fill valves
• Monitors inputs from the door lock and sensors to manage operation
• Failure can cause the washer not to start, stop mid-cycle, or fail to spin or drain
• Associated with control-related error codes or intermittent operation

• Disconnect power to the appliance before servicing
• Handle the board by the edges and use ESD protection to avoid static damage
• Label or photograph wiring; move connectors to the new board one at a time and verify ribbon-cable orientation
• Mount securely and ensure all harnesses are fully seated before restoring power and running diagnostics per the tech sheet

This 1-1/4" washer is a replacement flat washer used to secure fasteners and distribute load for reliable appliance assembly. It helps maintain proper clamping and prevents bolt/nut damage for stable operation. What it does:

• Sits under a nut or bolt head to spread load and protect mating surfaces
• Prevents fastener loosening caused by vibration or movement
• Reduces wear between joined parts to extend component life
• Helps maintain correct alignment of assemblies where used

• Turn off and unplug the appliance before beginning any repair
• Match this washer to the original by size and thickness to ensure a proper fit
• Use appropriate hand tools and replace any corroded or damaged fasteners at the same time

Replacement heater relay for Whirlpool appliances that controls power to the heating element. It restores reliable heat switching so cycles reach the correct temperature when the appliance calls for heat. What it does:

• Switches electrical power to the heating element when the control signals demand heat
• Replaces a failed relay that can cause no heat or intermittent heating
• Helps restore normal heating cycles and consistent performance
• Works with the appliance's control system to enable safe heating operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Use appropriate tools and avoid bending connector terminals; secure all wiring after replacement

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This door hinge supports and pivots the door for smooth opening and secure closing. Replacing a bent or worn hinge restores proper alignment so the door latches consistently and the appliance operates as intended. What it does and when to replace:

• Provides the pivot point between the door and cabinet
• Maintains door alignment with the catch/strike for a tight, reliable close
• Replace if the door sags, rubs, binds, or won't stay closed
• Help resolve no-start issues caused by the door switch not engaging

• 1 door hinge

• Disconnect power; shut off gas supply before servicing
• Support the door while removing/installing hinge screws to prevent strain or damage
• Transfer and reuse original mounting hardware as designed
• After installation, check and adjust latch/door-switch alignment as needed

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Includes ball bearing, rear bearing, water deflector, hose clamp, spacer, motor isolator, plug & Lip Seal

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

A replacement mounting screw to secure appliance panels and components so parts stay properly fastened during normal use. Small but essential hardware for stable, rattle-free operation and reliable repairs. What it does:

• Fastens panels, brackets or components to the appliance chassis
• Prevents loose panels, vibration noise, or parts shifting during operation
• Used when original screw is lost, damaged, or stripped
• Restores proper fit and alignment after disassembly for service

• Disconnect power and water before starting any repair
• Use the correct screw type and length; do not force or substitute oversized fasteners
• Tighten until snug—avoid overtightening to prevent stripped threads or cracked parts
• Keep small parts away from children and pets

A replacement push button for the appliance control panel that restores reliable user input and selection of settings. Use this button to replace cracked, worn, or unresponsive controls and return normal panel operation. What it does:

• Replaces a damaged or worn push button on the control panel.
• Restores tactile feedback and reliable button activation when the original is stuck, cracked, or non-responsive.
• Allows selection of appliance cycles and settings that rely on that specific control input.
• Works as a direct-fit panel button when the OEM part number matches.

• Disconnect power to the appliance (unplug or shut off circuit breaker) before beginning any work.
• Access typically requires removing the control or console; use appropriate screwdrivers and retain all fasteners.
• Inspect how the original button is mounted before removal—some buttons snap in, others seat behind the lens; if soldering or circuit-board removal is required, consider service.
• Confirm the OEM part number on your appliance and compare the replacement to the original before installation.

This front baffle grommet cushions and secures a dryer's front baffle to reduce vibration and noise while helping keep the baffle properly positioned during operation. Fits select Whirlpool-built dryers. What it does:

• Cushions the baffle to reduce rattling, knocking or squeaking noises during spin
• Holds the baffle in place to prevent movement or rubbing against the drum
• Helps maintain even drum rotation and prevents premature wear of plastic/metal parts
• Can wear or crack with age, causing noise or loose baffle symptoms

• High-level replacement — remove dryer front or access panel;
• Use proper tools and support panels; keep screws and fasteners organized for reassembly
• Disconnect power (and gas if applicable) before starting work

This display cover protects and finishes the appliance control panel, keeping the touchpad and display lens safe while restoring a clean, readable appearance. Replaces a cracked, faded, or scratched panel trim. What it does:

• Shields the control board area from dust, spills, and everyday wear
• Restores a clear view of the display and touchpad markings for easier use
• Improves the appliance's appearance by replacing damaged or discolored trim
• Helps prevent debris from interfering with buttons or electronic controls

• Disconnect power before starting any repair to avoid shock or damage
• Remove any outer trim or screws to access the control panel; handle the cover gently to avoid breaking retention clips
• Keep track of small fasteners and note orientation for correct reassembly
• Avoid touching circuit board contacts or components when replacing the cover