Maytag Mvw8450wq0 Parts

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

Located at the bottom of the basket, this impeller-style washplate rotates to move laundry and water for effective cleaning. Replace a cracked or stripped washplate to restore proper wash action and reduce noise and tangling.

• Creates water currents and friction to move clothes during the wash
• Transfers drive motion through the hub; worn splines can slip
• Helps circulate water and detergent through fabrics
• Common symptoms: weak or no agitation, grinding/clicking, wobbling/loose plate, visible cracks or broken fins

• Disconnect power and shut off water before service
• Remove the center cap and bolt; lift the old washplate straight up (work evenly if stuck)
• Inspect and clean mating splines; press the new washplate fully onto the shaft
• Reinstall and tighten the center bolt, replace the cap, and run a test cycle

This factory fastener secures appliance components so panels, brackets, and trim stay tight and aligned. Replace a missing or stripped screw to stop rattles, restore a secure fit, and keep parts mounted as designed.

• Fastens panels, brackets, covers, and trim to the chassis
• Restores proper alignment and reduces vibration or rattling
• Replaces missing, rusted, or stripped hardware
• Helps maintain a solid, factory-style fit after service

• Disconnect power (and water, if applicable) before servicing
• Match the original screw location and orientation; start threads by hand to avoid cross-threading
• Use the correct driver for the head type; tighten snugly without overtightening
• Reuse any original washers or clips if present

Color: White

The Dispenser Drawer Assembly is an OEM component specifically designed for Whirlpool washers. It houses detergent and fabric softener during cycles.

Causes of a faulty assembly can include warping of the plastic base from heat and chemicals over many loads. Small cracks may develop in the detergent trays.  

Symptoms of a bad dispenser drawer assembly include: 

• Leaks from cracked or misaligned drawers polluting washer interiors  
• Difficulty closing or securing the assembly properly
• Premature deterioration inhibiting reliable cycles 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.

• Mounts to the drive hub to rotate and circulate laundry during the wash cycle
• Helps create water currents and friction to loosen soils
• Worn or stripped splines can cause slipping and poor agitation
• Common symptoms: clothes not moving, poor cleaning results, unusual clicking/grinding from the tub base, visible cracks or wobble

• Disconnect power and shut off water before servicing
• Remove the center cap/cover, then remove the retaining bolt and lift off the old washplate
• Clean and inspect the hub splines; seat the new plate fully and reinstall the bolt—do not overtighten
• Run a short test cycle to ensure proper wash action

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

This is the washer's main electronic control board (ACU). It coordinates cycle timing and runs the motor, valves, and safety locks so your machine starts, advances, and finishes cycles consistently when the original control has failed. What it does:

• Directs wash, rinse, spin, and drain sequences based on cycle selection
• Regulates the drive motor, shift actuator, water inlet valves, and drain pump
• Monitors inputs from the lid lock and sensors to protect the machine and ensure proper operation
• Common failure symptoms: won't start or power up, cycle won't advance, fills but won't wash/spin, erratic or intermittent behavior

• One main control board assembly

• Disconnect power before servicing; use ESD protection and handle the board by the edges
• Photograph/label wire connectors; seat all plugs fully and secure any locking tabs
• Reinstall in the original mounting location; transfer any mounting clips or covers from the old board if applicable
• Some models require running a calibration or diagnostic cycle after replacement—follow the service manual

Small but essential, this drain hose retainer is a clip that secures the hose in place during use or storage. It keeps the hose properly routed to help prevent kinks, pull-outs, and leaks. What it does:

• Holds the drain hose to the cabinet/frame for correct routing or stowage
• Helps prevent kinks, abrasion, and strain that can cause poor draining or leaks
• Replaces a broken, warped, or missing retainer so the hose stays put
• Common symptoms: hose won't stay clipped, falls during operation, visible damage, water near hose path

• 1 drain hose retainer

• Disconnect power and turn off the water supply before servicing
• Access the hose routing area and remove the damaged retainer
• Position and fasten the new retainer in the same location; route the hose through it
• Run a brief test to ensure secure routing and no leaks

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

Note: Quantity of 1 pad, order as needed. Measures about 3.5" x 3.5".

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This recirculation hose routes wash water back through the tub during the cycle. A fresh, intact hose helps maintain proper water flow and prevents leaks, supporting consistent cleaning performance.

• Directs water from the pump back into the tub for continued circulation
• A cracked, kinked, or leaking hose can cause water leaks or poor wash performance
• Can help resolve issues like low recirculation flow or visible water drips during operation
• Restores correct internal water routing as designed

• Disconnect power and water supply before servicing
• Have towels or a shallow pan ready to catch residual water
• Note hose routing and clamp positions before removal; reuse or replace clamps as needed
• After installation, run a quick cycle to check for leaks and proper flow

The fabric softener dispenser stores liquid softener and automatically releases it during the rinse cycle. Replace a cracked, clogged, or missing dispenser to restore reliable dispensing and reduce leaks or softener left behind. What it does:

• Holds liquid fabric softener and dispenses it at the proper time in the rinse cycle
• Helps prevent early release of softener onto clothes
• Common symptoms: softener not dispensing, softener remaining in the cup after the cycle, leaks/drips from the dispenser area, or visible damage/missing dispenser
• Can resolve clogs from residue buildup that interfere with siphoning/flow

• 1 fabric softener dispenser

• Disconnect power and turn off water supply before servicing
• Remove the old dispenser (pull straight up or release locking tabs, per model)
• Clean any residue from the mounting area; flush the new dispenser with warm water
• Seat the new dispenser fully and test with a small amount of water to ensure proper flow

This lid bumper cushions the top-load washer lid as it closes, reducing noise and preventing direct contact between the lid and cabinet. Replace a missing or worn bumper to help protect the lid finish and ensure a smoother close.

• Provides a soft stop at the lid's contact point to absorb impact
• Helps reduce closing noise and lid rattle
• Helps prevent scuffs or chips on the lid edge or cabinet top
• Common signs of failure: bumper missing, flattened, cracked, or louder slam when closing

• Disconnect power before servicing the appliance
• Open the lid and locate the factory bumper position(s) per your parts diagram
• Remove the old bumper and any debris; seat the new bumper firmly in the designated location
• Close the lid gently to verify proper contact and alignment

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two