Mdb8969 Maytag Dishwasher Parts

This door latch strike is the catch mounted at the top of the dishwasher tub opening. It provides a secure engagement point for the door latch, helping the door close firmly so cycles can start and run properly. What it does:

• Serves as the latch catch on the tub/frame for the door latch to lock onto
• Helps ensure the door switch engages so the dishwasher will start
• Restores proper door alignment and closure if the original strike is bent, loose, or missing
• Common symptoms include door won't latch/close, dishwasher won't start, or door popping open mid-cycle

• 1 door latch strike

• Disconnect power at the breaker and turn off the water supply before servicing
• Open the door and remove the mounting screws securing the old strike
• Position the new strike, start screws by hand, and adjust so the latch engages smoothly; then tighten
• Test door closure several times and run a short cycle to ensure proper operation

This cover snaps over the upper rack height-adjuster mechanism to keep it secure and protected. Replacing a damaged or missing cover helps the upper rack stay level and maintain its selected position. What it does:

• Shields and retains the upper rack adjuster mechanism
• Helps the rack adjust smoothly and hold its set height
• Replaces a cracked, worn, or missing adjuster cover
• Symptoms include exposed adjuster parts, difficulty changing rack height, rack not staying in position, or a loose/tilted upper rack

• One rack adjuster cover

• Disconnect power to the dishwasher and shut off the water supply before servicing
• Pull out the upper rack to access the adjuster on the affected side
• Release the old cover's tabs, remove it, then align and firmly snap the new cover into place
• The rack adjusts and locks evenly on both sides

This mounting bracket secures an appliance component in the correct position, providing stable support and alignment. Replacing a damaged bracket helps stop looseness and vibration that can lead to noise, poor fit, or premature wear.

• Provides a rigid mounting point to hold the related assembly in place
• Restores proper spacing and alignment for consistent operation
• Helps reduce rattling, buzzing, or vibration from movement
• Replaces cracked, bent, or corroded brackets that no longer hold securely

• Disconnect power; shut off water supply if applicable
• Note the original orientation; transfer any clips, spacers, or grommets from the old bracket
• Reuse existing screws/fasteners; hand-start threads to avoid cross-threading
• Do not overtighten fasteners; confirm clearance and smooth operation before reassembly

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

This power cord connects your appliance to a household outlet. Replacing a worn or damaged cord restores safe, reliable power and can help resolve no-power or intermittent power issues caused by a compromised lead.

• Delivers electrical power from the outlet to the appliance
• Replaces cords with cracked, frayed, or heat-damaged insulation or a damaged plug
• Helps when the unit won't power on or loses power when the cord is moved
• Addresses visible scorching, arcing, or melting on the cord or plug

• Disconnect power before servicing; verify no voltage is present
• Note wire positions or take a photo before removal; match to the same terminals on install
• Use the proper strain relief/clamp and route away from sharp edges, moving parts, and heat sources
• Confirm the ground connection is secure; do not modify the plug

Color: Black

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This part replaces the left-side rack height adjuster in your dishwasher. It supports and locks the rack at the selected position so dishes load easily and the rack stays level throughout the cycle.

• Controls and supports rack height on the left side
• Helps keep the rack level; a failed adjuster may cause a drop or tilt
• Common symptoms: rack won't raise/lower, left side sags, rack binds or is hard to slide
• Restores smooth rack movement and consistent loading height

• Disconnect power and water supply before servicing.
• Pull the rack forward, remove end caps/stops, and lift the rack out.
• Remove the damaged adjuster and install the new one on the left side (as viewed from the front). Reuse existing hardware as applicable.
• Reinstall the rack and verify smooth travel and proper height adjustment.

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

This replacement support restores a firm, level mount for its paired component inside your appliance. It keeps the part properly seated and aligned so shelves, racks, bins, or mechanisms remain stable and operate as intended. What it does:

• Secures the mated component in the correct position
• Maintains alignment and level support during use
• Helps prevent wobble, sagging, binding, or disengagement
• Common signs of failure: cracked or missing support, loose/uneven fit, rattling, component won't stay seated

• 1 support

• Disconnect power and shut off water supply before servicing.
• Remove the affected component to access the support and note orientation.
• Transfer/reuse original screws or clips if required by your design.
• Seat the new support fully; if the design uses paired supports, inspect/replace both for even alignment. Test operation.

Restore smooth, secure height adjustment to your dishwasher's upper rack with this right-hand rack adjuster. Replacing a cracked or worn adjuster keeps the rack level and properly attached to the rail for dependable loading and cleaning.

• Raises/lowers and locks the upper rack on the right side
• Keeps the rack aligned and secured to the slide rail
• Helps the rack move smoothly during loading and unloading
• When worn or broken, symptoms can include a sagging right side, rack that won't adjust height, binds or jumps off the track, or visible cracks

• Disconnect power to the dishwasher before servicing
• Remove the upper rack by releasing the end stops on the rails
• Move any rack clips or screws from the old adjuster to the new one as required; install on the right side when facing the appliance
• Reinstall the rack and end stops, then verify smooth travel and proper height engagement

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679