Mdbh949awq Parts

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks

This is the dishwasher upper spray arm that delivers water across the top rack for effective cleaning. It replaces a worn or damaged spray arm to restore proper water distribution and rinse performance. What it does:

• Spins and sprays water across the top rack to help remove food and detergent residue
• Restores proper spray pattern when the original arm is cracked, clogged, or not turning
• Helps prevent poor cleaning, spots, or missed areas on top-rack dishes
• Works with the dishwasher's water delivery system to maintain rinse and wash coverage

• One upper spray arm

• Turn off power and water to the dishwasher before beginning any service
• Inspect and clear any debris from the spray arm and the mounting area before installation
• Hand-tighten or snap the arm into place per your model's instructions; avoid overtightening

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

This standpipe houses the washer's overfill control and directs excess water into the drain path, helping prevent overfilling and internal flooding. It's a direct-fit replacement for the factory overfill control housing. What it does:

• Provides the sealed channel for excess wash water to flow to the drain
• Supports and locates the overfill/level control assembly
• Helps stop water from overflowing the tub and causing leaks
• Can resolve symptoms like unexplained overfilling, water leaking at the washer base, or fill-level issues

• Disconnect power and shut off water before starting any repair
• Access may require removing the washer top or control housing
• Inspect surrounding gaskets and hoses for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; test operation after reassembly

This sump tab secures the dishwasher's sump assembly to the tub opening, keeping it properly aligned and sealed. Replace a broken or missing tab to address movement, rattling, or leaks originating from the sump area.

• Locks the sump assembly to the tub/base opening
• Helps maintain the sump-to-tub seal to limit leaks
• Keeps the pump intake and fine filter area properly positioned
• Common symptoms: leaks under the unit, loose/shifted sump or filter, rattling/vibration from the sump area

• Disconnect power and water supply before servicing
• Access the sump per your model (from inside the tub by removing lower rack/filters, or from below after removing the toe panel)
• Ensure the sump and gasket are fully seated; install the new tab until it locks securely
• Run a brief fill/drain test and check for leaks before reassembly

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This overfill switch monitors water level and signals the appliance to stop filling to help prevent overflows. Use it to restore correct water-level control when the original switch fails or malfunctions. What it does:

• Detects excess water and interrupts the fill cycle as a safety cutoff
• Works with the washer's control to maintain proper water level
• Common symptoms of a failing switch: continuous filling, overfilling, or water-level related error codes
• Can also cause cycles to stop or not advance if the machine thinks tank is overfilled

• One overfill control switch

• Disconnect power and water supply before servicing to avoid shock or flooding
• Typically located behind the control console or rear access panel
• Handle wiring connectors gently and secure all connections before testing

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

Size: 8-32 x 1/2 inch.

Color: Bisque

This motor-pump assembly replaces the washer's drain pump to restore reliable water removal and reduce leaks. It mounts to the tub and handles draining so your cycle can finish and clothes can spin out properly. What it does:

• Pumps water out of the washer during drain cycles to allow proper spin and cycle completion
• Helps prevent standing water and reduces the chance of overflow or tub leaks
• Stops humming, grinding, or no-drain symptoms caused by a failed pump motor
• Works as the integrated motor and pump unit that attaches to the washer tub

• Disconnect power and water before servicing; follow all safety precautions
• Basic hand tools required; access may require removing front or rear service panel
• Inspect and reinstall hoses and clamps securely to prevent leaks