Med Hook Tromm Air Filter Parts

This inlet hose is the internal water line for your dishwasher, routing fresh water from the fill valve into the wash system. Replacing a brittle or leaking hose restores reliable filling and helps protect floors and cabinetry from water damage.

• Channels incoming water from the inlet valve to the tub/sump
• Maintains proper fill level and flow at the start of each cycle
• A cracked, kinked, or loose hose can cause leaks or slow/no fill
• Restores correct water delivery and helps prevent water damage

• Disconnect power and shut off the water supply before servicing
• Pull the dishwasher forward for access; place a towel or pan to catch residual water
• Note the original routing and clamp positions; transfer clamps and avoid kinks
• Restore water, run a quick fill cycle, and check all connections for leaks

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks

Color: blue. Measures about 2-1/2 inches wide by 4-1/2 inches deep.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This metal door hinge secures and guides the refrigerator door, restoring proper alignment and smooth opening. Replace a worn or damaged hinge to stop sagging doors and reduce binding or uneven gaps for a reliable seal and easy access. What it does:

• Provides pivot support so the door opens and closes smoothly
• Keeps the door aligned to maintain an even gasket seal and consistent cooling
• Replaces bent, worn, or noisy hinge hardware that causes door sagging or rubbing
• Helps prevent further wear to the cabinet and door by restoring correct movement

• One door hinge

• Unplug the appliance and empty or support the door before removing hinge hardware
• Use the correct tools and keep track of screws and any shims or spacers
• Check door alignment and gasket sealing after installation; adjust as needed

This tub cover forms the front half of the washer's outer tub. It seals the tub and provides the mounting lip for the door boot, helping prevent leaks and keeping the spin basket properly aligned with the cabinet opening.

• Seals the front of the outer tub and provides a secure seat for the door boot/bellows
• Contains wash water during all cycles to prevent leaks and splashing
• Maintains proper clearance for the spin basket to avoid contact with the front opening
• Common failure symptoms include leaks at the front or bottom of the cabinet, visible cracks/warping, or the door boot repeatedly coming loose or tearing

• Disconnect power and water; wear gloves and protect sharp edges
• Remove top and front panels; release the outer boot clamp and peel the door boot from the front panel. Detach any hoses/wiring from the cover, remove the perimeter bolts, and transfer any fittings from the old cover
• Clean sealing surfaces; inspect/replace the tub-to-cover gasket if your model uses a separate one. Seat the new cover and tighten fasteners evenly in a crisscross pattern
• Reinstall the boot and clamp carefully, reassemble the cabinet, and run a fill/spin test to check for leaks

The Incandescent Lamp is an OEM part for LG dryers. It serves as the interior light source for LG clothes dryers.

Causes of lamp failure relate to typical lifespan expirations, being accidently left on which shortens rated hours, or faulty sockets allowing moisture or other contamination to enter the connection points.

Symptoms of a burned out lamp include:

• Dark or completely unlit drum chamber interior
• Inability to fully inspect clothes during operation
• Difficulty monitoring dryer progress without supplemental lighting

This LG part is also compatible with some Kenmore models.

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This cabinet hole cap plugs unused hinge or screw openings on the dryer cabinet. It restores a clean, finished look and helps keep lint and moisture out after a door reversal or service. What it does:

• Covers open hinge/screw holes on the dryer cabinet
• Helps block lint, dust, and moisture from entering through unused openings
• Restores a finished appearance; helps prevent snags around exposed holes
• Commonly replaced when a cap is missing, cracked, or loose

• 1 cabinet hole cap

• Disconnect power before working near the cabinet
• Remove any damaged cap and clean the opening
• Press the new cap into the hole until fully seated and flush
• Wear gloves; cabinet edges and holes can be sharp

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit