Mgr5750aw Parts

This snap-in indicator light assembly mounts in the control panel and illuminates when a function is active. Replace a failed or damaged indicator to restore clear status feedback on your range or wall oven.

• Provides visual indication that a selected function is active
• Restores at-a-glance status on the control panel
• Common symptoms: indicator won't light, flickers, stays on constantly, or the lens/housing is damaged
• Direct replacement for the original snap-in lamp assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the rear of the control panel; note wire locations or take a photo
• Depress the retaining tabs to release the old light; transfer wires to the new assembly and snap it fully into place
• Restore power and verify indicator operation

Color: clear. Measures about 3 inches in diameter.

For screws order: WP7101P485-60.

This drawer roller supports and guides the lower range drawer so it slides smoothly on its track. Replacing a worn or broken roller restores easy operation and helps prevent the drawer from binding, sagging, or coming off the track.

• Supports the storage/warming drawer as it opens and closes
• Helps keep the drawer aligned on the rails to prevent tilting or popping off
• Reduces friction for smoother movement and less noise
• Typical failure signs: sticking drawer, rough/grinding movement, sagging front, or a cracked/flat-spotted wheel

• Disconnect power and allow the appliance to cool completely
• Remove the lower drawer to access the rollers
• Detach the fastener or retainer, install the new roller in the same orientation, and secure it
• Reinstall the drawer and verify smooth travel and proper engagement on both tracks

This oven gas valve controls the flow of gas to the oven burner. When functioning properly, it allows the burner to ignite and maintain a steady flame for consistent preheating and baking performance.

• Opens and closes to supply gas to the oven burner as commanded by the control system
• Helps ensure gas only flows when ignition is called for
• Common symptoms include no heat/no flame, slow preheat, or temperature not reaching set point
• May also present as intermittent heat or a weak/irregular burner flame

• Disconnect power and shut off the gas supply before servicing
• Verify igniter condition/current; a weak igniter can mimic a failed valve
• Transfer any required fittings or brackets from the original valve
• Use gas-rated thread sealant on threaded joints; leak-test all connections and run a test cycle to proper ignition

A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:

• Provides a fixed-diameter shoulder for pivots, spacers, or mounting points in assemblies.
• Holds panels and moving components at the correct distance to prevent binding or friction.
• A missing or worn shoulder screw can cause misalignment, rattling, or loose parts during operation.
• Used where a smooth-bearing surface and controlled clearance are required between parts.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing.
• Handle small fasteners carefully to avoid dropping into assemblies; magnetic pickup tools can help.
• Start threads by hand to avoid cross-threading; tighten snugly but avoid overtightening.

Color: White

This is a genuine lock nut replacement. This is a general piece of hardware that is often used on several types of lawn and garden equipment, including in engines, housing, and other areas. The exact application of this part will vary based on the unit. The lock nut is used to create a more secure seal than a standard nut. When properly secured, the lock nut tightens to a bolt and uses an extra locking washer with teeth to ensure a snug fit.If lock washers do get damaged or lost, they need to be replaced immediately with a genuine OEM replacement. This model is compatible with all types of machines and units since it is a generic part. The washer is sold as an individual part and manufactured by Whirlpool. Lock nuts will need to be installed using a socket wrench or adjustable wrench. Pliers, a screwdriver, or another socket wrench will be needed to hold the bolt while the lock nut is being secured in place. Be sure to thread the lock nut carefully to ensure a strong seal and avoid stripping the bolt or the nut.

This sheet-metal pan-head screw secures appliance panels, brackets, and components to the cabinet or frame. Replacing a missing or damaged screw restores a tight fit and helps stop rattles, misalignment, and loosening.

• Fastens sheet-metal panels, covers, ducts, and brackets to the appliance chassis
• Helps keep components aligned and secure during operation
• Replace if the original is missing, rusted, stripped, or damaged
• Common symptoms: loose or vibrating panels, gaps or misaligned parts, hardware that won't tighten

• Disconnect power; shut off gas or water supply before servicing
• Support the panel or part being attached; hand-start threads to avoid cross-threading
• Use the correct driver bit; tighten snugly but do not overtighten into sheet metal
• If multiple matching screws secure a part, consider replacing them as a set for consistent hold

Color: White. For black order WP98008545. For biscuit order 98008169.

Screws for range anti tip bracket: WP3801F656-51. Includes 2 screws.

Size: 10-24 x 3/8 inch.

The Snap Nut is an OEM part for Whirlpool ovens and ranges. It is used to secure various components within the appliance, providing a reliable and easy-to-install fastening solution. The snap nut ensures that parts such as panels and assemblies remain firmly in place during operation.

Causes of a bad snap nut can include wear and tear from regular use, over-tightening during installation, or damage due to impacts or vibrations.

Symptoms of a bad snap nut include:

• Loose or wobbly components within the oven or range
• Parts not staying securely attached
• Unusual noises from vibrating or rattling parts during operation
• Difficulty in assembling or disassembling parts

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

This igniter switch operates the burner lighter so the cooktop sparks and lights a gas burner when you press the lighter control. Replacing a faulty switch restores consistent ignition and reliable burner starting. What it does:

• Sends the ignition spark to the burner when the lighter/push-button is pressed.
• Replaces a worn, sticky, or unresponsive lighter switch that prevents consistent sparking.
• Common symptoms it can address: no spark from the lighter, intermittent sparking, or a button that fails to activate ignition.
• Interfaces with the existing lighter mechanism and wiring to restore normal ignition function.

• Disconnect power (unplug) and shut off the gas supply before starting any work.
• Access typically requires removing the cooktop or control panel; use appropriate hand tools and keep track of fasteners.
• Avoid touching electrical contacts and confirm wiring matches the original during reassembly.

This white valve knob replaces a worn, cracked or missing control knob so you can safely and easily adjust burner or oven settings. It restores a secure grip and precise control for temperature or flame adjustments. What it does:

• Replaces a damaged or stripped control knob used to turn gas or electric valve controls
• Provides a positive grip so settings can be changed smoothly and accurately
• Helps stop slipping or spinning that prevents proper temperature or flame adjustment
• Matches original fit to engage the control shaft properly when installed

• Turn off power and gas supply before removing the old knob
• Pull off the old knob straight from the control shaft; align splines and push new knob fully onto the shaft
• Do not force or hammer the knob; ensure it seats squarely to avoid damage
• Test control operation after installation and restore power/gas only when connection is secure