Mgt3800xw Parts

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

Used from harness to top.

This LP gas conversion label identifies that the appliance has been converted for use with liquid propane. Applying it near the gas valve/regulator clearly communicates fuel type for safe service, troubleshooting, and future installation decisions.

• Marks a converted unit as LP fuel to prevent misdiagnosis or incorrect hookups
• Provides quick visual identification for technicians and inspectors
• Replaces a missing, damaged, or illegible conversion label
• Use when a conversion has been completed and the original label is not present

• Apply only after completing the correct LP conversion procedure for your specific model
• Clean and dry the mounting surface; place the label where specified (typically near the gas valve/regulator or rating plate)
• Do not cover existing safety or rating labels; press firmly to ensure full adhesion
• Leak-check all fittings before returning the appliance to service

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This agitator auger is the upper portion of a two-piece washer agitator. It works with the cam and dogs to create the one-way ratcheting motion that moves clothes through the wash for proper turnover and cleaning.

• Provides the one-way ratcheting action of the upper agitator
• Interfaces with the agitator dogs and cam to move clothes through wash water
• When worn or cracked, the top agitator may stop moving while the bottom still agitates
• Symptoms can include poor turnover, laundry staying on top, or clicking during agitation

• Disconnect power and water supply; wear cut-resistant gloves.
• Remove the fabric softener dispenser and inner cap, then remove the agitator bolt to lift off the old auger.
• Inspect/replace the agitator dogs and cam while servicing; transfer reusable caps if applicable.
• Align the splines, seat the new auger, reinstall the bolt and caps, and test agitation.

Left valve coil that powers the solenoid on a water inlet/valve assembly to control water flow. Replacing a worn or burnt coil helps restore proper valve operation so the dispenser or ice maker can fill when called. What it does:

• Energizes the left solenoid on the inlet/valve assembly to open and close the valve when the appliance requests water.
• Used when a coil is damaged, burnt, or not producing the magnetic field needed to actuate the valve.
• Common symptoms: no water to dispenser or ice maker, weak or intermittent flow, humming or buzzing from the valve, or visible burn/discoloration on the coil.
• Matches the OEM function for the left-side solenoid.

• Disconnect power and shut off the water supply before servicing the valve assembly.
• Note wiring and coil orientation before removal so the replacement installs in the same position.
• Handle the valve plunger and seating components carefully; do not contaminate valve seals or passages.
• If wiring terminals are corroded or damaged, replace connectors.

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

Replacement plug button that snaps into place to cover a small access hole or fastener opening. Restores a finished appearance and helps keep dirt, moisture and small objects out of the appliance cavity. What it does:

• Covers exposed holes or mounting openings for a clean, finished look
• Prevents dirt and debris from entering small internal cavities
• Replaces missing, cracked or worn plug buttons that no longer stay seated
• Small, low-profile design to match factory appearance

• Disconnect power to the appliance before servicing
• Typically installs by pressing into the opening until it snaps flush; a small flat screwdriver can assist
• Avoid prying against surrounding trim to prevent cosmetic damage
• Keep small parts away from children and pets

Replacement housing that supports and protects internal components in compatible Whirlpool appliances. Restores structural integrity to the cabinet, helping reduce vibration and keeping wiring and components enclosed for safe, reliable operation. What it does:

• Provides the outer cabinet support that secures motors, controls and wiring
• Protects internal parts from debris and accidental contact
• Helps reduce rattling, vibration and misalignment symptoms caused by cracked or damaged cabinets
• Restores proper fit for panels and fasteners to eliminate rubbing or interference noises

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; keep screws and clips organized during disassembly
• Some housings may require two people to position during replacement—avoid forcing parts to prevent damage
• Fasteners and any sealing gaskets are in good condition and replaced if worn

This light socket holds the appliance bulb and provides a reliable electrical connection, restoring clear visibility inside your unit. Replace a cracked, heat-damaged, or loose socket to fix lights that flicker, go out, or won't stay seated.

• Secures the bulb and makes proper electrical contact with the wiring
• Powers the bulb when the control or door switch commands illumination
• Helps maintain consistent lighting during normal operation
• Typical symptoms: light won't turn on with a good bulb, flickers, intermittent lighting, burnt or brittle socket, bulb won't stay seated

• Disconnect power to the appliance before servicing; allow hot areas to cool
• Note wire locations and socket orientation; take a photo before removal
• Transfer any mounting screws/bracket from the old socket as needed
• Install the correct bulb type and wattage per your appliance manual; do not overtighten

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

Size: .20 Fl. Oz. (6 ml)

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly