Mlga2000ww Parts

This spring clip secures small panels, brackets, or trim inside your appliance to maintain a snug fit and prevent movement. Replacing a fatigued clip helps restore proper alignment and reduce unwanted vibration or rattling. What it does:

• Provides spring tension to hold a component firmly in place
• Helps prevent vibration, rattling, or shifting during operation
• Replaces a bent, worn, corroded, or missing clip
• Common symptoms: loose or misaligned panel/trim, recurring rattles, or parts that won't stay secured

• 1 spring clip

• Disconnect power (and gas, if applicable) before servicing
• Access the clip location per your model's service/parts diagram
• Note the clip's orientation and attachment points before removal
• Use needle-nose pliers carefully to avoid bending adjacent tabs or brackets

This inner outlet hose routes water from the unit's internal pump/sump to the discharge path. Replacing a cracked, kinked, or clogged hose restores proper water flow and helps prevent leaks or cycle interruptions.

• Directs water from the internal pump/sump to the outlet within the machine
• Maintains a watertight path when secured with clamps
• Wear, heat, or mineral buildup can cause cracks, kinks, or blockages
• Common symptoms: leaks inside/under the unit, slow or no draining, restricted flow, or drain-related error messages

• Disconnect power and turn off the water supply before servicing
• Expect residual water; place towels or a pan to catch spills
• Note hose routing and clamp positions; transfer existing clamps or install new ones
• Seat the hose fully on fittings, tighten clamps evenly, and perform a short test run to check for leaks

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

This washer bellow, also called the door boot seal, forms the watertight gasket between the front door opening and the outer tub. Replacing a worn or torn bellow helps stop front leaks and keeps wash water inside the machine.

• Creates a watertight seal between the door opening and outer tub on front-load washers
• Helps prevent water on the floor from leaks at the door area
• Common failure signs: water leaking from the front/door, visible tears or cracks, persistent mildew/odor on the gasket, or the seal pulling loose

• Disconnect power and turn off water supply before service
• Remove the outer retaining clamp, then access and remove the inner clamp as required by your model
• Note orientation marks/drain openings on the bellow and seat it evenly on both the tub and front panel
• Reinstall clamps securely and run a brief test fill to check for leaks

This water inlet valve regulates the flow of water into the washer tub and dispenser compartments. When it wears or sticks, the machine may fill improperly or at the wrong times; replacing it restores controlled filling and dispensing. What it does:

• Directs hot/cold water to the tub and dispenser channels as selected by the control.
• Uses four solenoids to open/close individual water paths during fill and rinse.
• Common symptoms: won't fill or fills slowly; keeps filling when off; water drips into tub between cycles; incorrect temperature; a dispenser bay doesn't flush.
• Addresses internal leaks, stuck or shorted coils, or sediment-clogged inlet screens causing restricted flow.

• Water inlet valve assembly (4 solenoids)

• Disconnect power and turn off both water supplies before servicing.
• Place a towel to catch residual water; note hose locations and relieve pressure before removal.
• Move electrical connectors to the matching terminals one at a time; transfer hoses securely.
• Open supply valves and check all connections for leaks; run a fill cycle to operation.

Keep the drive system running smoothly. This idler pulley maintains proper belt tension and tracking so the drum/tub or drive system turns quietly and reliably, helping prevent squeal, slip, and premature belt wear. What it does

• Maintains constant tension on the drive belt to prevent slipping
• Guides the belt for smooth, consistent rotation of the drum/tub or drive system
• Helps reduce belt noise and premature belt wear
• Common symptoms of a worn pulley include squealing/scraping noises, burning rubber smell, the belt coming off or fraying, or no tumble/agitate/spin

• 1 idler pulley

• Disconnect power; turn off gas supply before servicing
• Access the belt path and note routing before removal
• Relieve belt tension, remove the old pulley, and install the new pulley in the same position; ensure the belt is seated on all pulleys
• Manually rotate the system to verify smooth operation before reassembly and testing

This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.

• Encloses and supports the blower wheel while channeling air from the drum to the exhaust
• Maintains correct airflow and back pressure for efficient drying performance
• Replace if the housing is cracked, warped, melted, or otherwise damaged
• Typical symptoms include weak vent airflow, longer dry times, rattling or scraping from the blower area, or visible lint leakage

• Disconnect power; if gas, also shut off the gas supply
• Access the blower area by removing the lower/front panel and lint ducting as required by your model
• Transfer the blower wheel and any brackets from the old housing; clean lint from ducts before reassembly
• Ensure the housing seats fully and all duct connections are tight; spin the blower by hand to verify clearance before restoring power

This is a genuine replacement handle that restores a secure, comfortable grip for opening and closing your appliance. Use it to replace a cracked, broken, or missing handle and bring back a clean, factory look and feel. What it does

• Provides a sturdy grip to operate the appliance door or drawer
• Restores proper fit and alignment with existing mounting points
• Improves usability when the original handle is loose or damaged
• Common symptoms: cracked or broken handle, looseness, missing handle, cosmetic wear

• One handle

• Disconnect power to the appliance before beginning work
• Remove the fasteners from the old handle and transfer any reusable hardware
• Align the new handle with the mounting points; start all screws by hand to avoid cross-threading
• Tighten evenly without over-torquing; test operation after installation

This replacement handle restores a secure, comfortable grip for opening and closing your appliance. Swap a loose, cracked, or missing handle to improve safety, day-to-day usability, and the overall appearance of your unit.

• Provides the grip point to open and close the door or drawer
• Mounts to existing attachment points for a stable, aligned hold
• Helps resolve issues such as a wobbly, cracked, or broken handle
• Restores smooth, confident operation when pulling the door

• Disconnect power to the appliance before starting any repair
• Support the door/drawer and remove the interior fasteners holding the old handle
• Transfer any trim/end caps if present; position the new handle and start screws by hand
• Tighten fasteners evenly without overtightening; test operation

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)

To order indicator lens use WP22001948.

This cabinet spring secures the appliance cabinet to the frame to control movement and vibration. Replacing a fatigued or broken spring restores cabinet stability and helps reduce rattling and excessive shaking during operation.

• Anchors the cabinet to the chassis to maintain proper alignment
• Helps limit vibration and noise during use
• Supports correct fit of cabinet panels and top
• Typical failure signs: loose or shifting cabinet, rattling, or increased vibration

• Disconnect power before servicing; allow all moving parts to stop
• Support the cabinet or panel to relieve spring tension before removal
• Spring is under tension—use suitable pliers/spring tool and wear eye protection and gloves
• After reassembly, verify the cabinet is level and securely fastened

Color: white. It measures about 12-1/2 inches wide by 8 inches high.

Service tub gasket that creates a watertight seal between the washer tub and cabinet. Replaces a worn or damaged seal to help stop leaks and limit water damage around the appliance. What it does:

• Seals the tub opening to prevent water from leaking onto the floor during fill, wash and drain cycles.
• Restores the seal that keeps moisture confined to the tub and reduces mildew buildup at the tub edge.
• Helps eliminate spray and dripping that can occur with cracked, torn or hardened gaskets.
• Supports normal drum/tub operation by maintaining the intended tub-to-cabinet seal.

• Disconnect power and shut off water supply before starting any repair.
• Inspect and clean mating surfaces before installing the new gasket; ensure proper orientation and seating into the groove or mounting channel.
• Use original clamps or fasteners and tighten evenly; replace any missing or damaged mounting hardware before testing for leaks.