Mveb765fw1 Parts

The Interlock Door Switch is an OEM part for LG microwaves. It is a safety component located on the door of the microwave designed to prevent the microwave from operating unless the door is securely closed. The interlock door switch works with the microwave's electronic control board to sense when the door is open or closed and allow or disallow operation accordingly.

Causes of a bad interlock door switch can include normal wear and tear from repeated opening and closing of the microwave door over time.

Symptoms of a bad interlock door switch include:

• The microwave runs or heats with the door open
• Error codes or diagnostic messages related to door sensors on the control board
• The microwave fails to operate even when the door is securely closed

This OEM LG part is also compatible with some Sears/Kenmore microwaves.

Inner plastic door film covers the holes in the inner door frame.

This is the turntable assembly for the microwave's rotating tray system. It provides a stable, smooth-rotating surface so dishes stay level and heat evenly, replacing a damaged, wobbly, or missing turntable to restore consistent cooking performance. What it does:

• Forms the rotating surface that supports dishes for uniform heating
• Keeps the tray centered and aligned with the drive hub/guide for smooth motion
• Replace if the tray is cracked, chipped, or missing
• Replace if the tray rocks, binds, or skips while turning
• Helps address uneven heating caused by poor or inconsistent rotation

• 1 turntable assembly

• Unplug the microwave or switch off power at the breaker before servicing
• Remove the existing turntable parts and clean the track/hub area
• Set the new assembly so it sits flat and engages the drive hub; verify smooth, unobstructed rotation
• Do not operate the microwave without the turntable properly installed

This front decor panel is the cosmetic trim piece for the appliance's front side. It finishes the opening/control area and covers mounting points, restoring a clean, secure factory look when the original trim is cracked, loose, or missing.

• Provides a clean, finished appearance at the front assembly
• Helps cover fasteners and raw edges; may help support adjacent fascia
• Helps keep dust and debris out of internal areas
• Common symptoms: cracked or missing trim, broken tabs, discoloration, or a loose/rattling front panel

• Disconnect power before servicing
• Remove screws or release retaining clips from the original trim; keep hardware for reuse
• Transfer any clips, foam, or badges from the old part if needed, then align and secure the new panel and verify clearances

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This replacement holder/locker secures the door latch assembly so the door stays aligned and closes reliably, allowing the appliance's safety interlocks to engage and the unit to operate as intended. What it does:

• Supports and holds the door latch/latch assembly in the correct position
• Helps keep the door aligned and firmly closed so safety switches can engage
• Can resolve symptoms like a door that won't stay closed, door rattling, or the appliance failing to start due to an incomplete door closure
• Matches OEM service-panel location and function for straightforward swap-out

• Disconnect power (unplug or shut off breaker) before beginning any work
• Access may require removing the outer cabinet or control panel per the appliance service instructions
• Handle door and latch components carefully to avoid misalignment or damage

This door frame assembly replaces a damaged or warped outer door frame to restore proper fit and finish. It re-establishes a stable support for the door and helps the appliance close and seal correctly. What it does

• Provides the structural outer frame that supports the door and inner components.
• Restores correct door alignment and reduces gaps that can cause rattling or poor closure.
• Helps prevent debris and moisture from entering the door cavity.
• Useful when the existing frame is cracked, bent, or cosmetically damaged.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle any glass or trim pieces carefully to avoid breakage or injury.
• Replacement typically requires removing the door from its hinges and detaching exterior trim; keep fasteners organized.

This glass turntable plate fits microwave ovens to provide a stable, rotating surface for cookware and food, helping heat items more evenly and preventing spills during operation. What it does:

• Supports dishes and containers while the microwave's turntable motor rotates them
• Promotes more even heating by allowing food to rotate during cooking
• Replaces cracked, chipped, or missing microwave glass plates
• Restores safe, stable operation when the original plate no longer seats properly

• Handle carefully; glass may be heavy or break if dropped
• Place the plate onto the microwave's roller guide/turntable support so it seats securely
• Clean with mild detergent and avoid abrasive cleaners to preserve the finish
• Do not operate the microwave without the turntable and support properly installed

This supporter holder is a replacement mounting bracket that secures internal components and helps maintain proper alignment for stable operation. Install the bracket to replace a cracked, broken, or missing holder and reduce movement or noise. What it does:

• Secures and supports internal assemblies or panels to keep parts aligned.
• Replaces cracked, broken, or missing holders that allow components to shift.
• Designed to match OEM mounting locations for a direct-fit replacement when used with the correct part number.

• Disconnect power (and water supply if applicable) before beginning any repair.
• Use basic hand tools; save original fasteners or replace damaged hardware with identical fasteners.
• Inspect adjacent parts and mounting points for damage and replace if necessary for a secure fit.

This U-bending case is the plastic housing that protects and routes the refrigerator evaporator's U-shaped tubing and helps direct airflow across the evaporator for effective cooling. It replaces a damaged or missing evaporator cover to restore proper airflow and protect tubing. What it does:

• Shields the evaporator U-bend and nearby tubing from contact and damage
• Directs airflow over the evaporator for more even cooling
• Helps keep frost and debris away from the evaporator assembly
• Prevents vibration noise caused by loose or damaged covers

• Always disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer evaporator cover/panel; keep fasteners organized
• Handle the evaporator and tubing carefully to avoid punctures or bending

This is a replacement plastic filter cover that secures and protects the appliance filter, helping maintain proper airflow and filter positioning for reliable operation. Fits into the filter housing to keep the filter sealed and supported. What it does:

• Holds the appliance filter in place to prevent shifting during operation
• Protects the filter from accidental damage and large debris
• Helps maintain proper airflow and filtration performance when installed correctly
• Commonly replaced when cracked, warped, missing, or no longer latching securely

• Disconnect power to the appliance before servicing to avoid electrical or mechanical hazards
• Remove the old cover by releasing any tabs or screws, then align new cover tabs into the housing and snap or fasten into place
• Do not force the cover; ensure proper alignment to avoid damaging mounting tabs
• If clips or screws are damaged, replace them before operating the appliance