Mvw8700vq0 Parts

This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:

• Distributes power and control signals to lower-cabinet components
• Supports proper operation of the drive motor, drain pump, and related parts
• Typical symptoms: no spin or agitate, won't drain, intermittent operation, or visible heat damage/corroded connectors
• Match by part number for correct fit on 4.7/4.8-cu ft platform models

• 1 lower wire harness assembly

• Disconnect power and water supply before servicing
• Access the underside per your model (tilt the washer or remove panels as required)
• Transfer one connector at a time; route along the factory path and secure with existing clips/ties away from moving parts and sharp edges
• After installation, run a diagnostic or test cycle to normal operation

The Drain Hose is an OEM part for Whirlpool washing machines. It is a flexible tube that diverts water from the washer tub during drain cycles, guiding it out of the appliance and into a nearby drain source such as a sink. 

Causes of a bad drain hose can include cracks or abrasions developing over time due to repeated bending and flexing during drain cycles. Mineral or hard water buildup inside the hose can also lead to clogs. Other potential causes are physical damage from rodents, pets, or accidental punctures.

Symptoms of a bad drain hose include:

• Incomplete draining or water remaining in the washer tub after cycles  
• Leaks or drips forming around the drain hose connection point
• Puddles or water pooling under or around the washing machine
• Slow drainage during spin cycles

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washer models.

The Lid is an OEM part for Whirlpool washers. It covers and secures the washing machine drum during operation, ensuring safe and efficient washing.

A bad washer lid can be caused by regular use, accidental damage, or wear and tear over time. If you notice issues such as a loose or broken lid, difficulty in closing or latching the lid, or if the lid is not staying securely in place during the wash cycle, it may indicate a problem with the washer lid.

Symptoms of a bad washer lid include:

• Lid not closing or latching properly
• Excessive vibration or movement during the wash cycle
• Water leaking from the top of the washer

Replace your faulty washer lid with this genuine OEM part to restore your washing machine. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This electronic control board manages your appliance's core electronic functions so controls, displays and automated cycles operate correctly. Replacing a failed board restores proper control and resolves many electronic-related faults. What it does

• Receives input from user controls and sensors to run timed cycles and system functions
• Sends signals to relays, valves and compressors to start, stop or modulate components
• Common symptoms: blank or unresponsive display, unresponsive controls, or erratic/incorrect operation
• Also associated with inability to start or intermittent power to key components

• One electronic control board

• Disconnect power to the appliance before beginning any service
• Handle the board by its edges and avoid touching circuit traces or components
• Reconnect all wiring harnesses to their original locations and ensure connectors are fully seated

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.

This ACU assembly is the electronic control module that handles user inputs and communicates with other appliance systems to restore responsive controls and normal operation. Install to replace a faulty or unresponsive control unit. What it does:

• Receives signals from the control panel and routes commands to motors, valves, and sensors
• Helps resolve symptoms like an unresponsive control panel, buttons that do not register, or the appliance failing to start cycles
• Interfaces with other control boards and sensors to coordinate appliance functions
• Clears intermittent operation caused by a damaged or failing control module

• Disconnect power to the appliance before beginning work to avoid shock risk
• Use care with wiring connectors and mounting hardware; label connectors if needed for reassembly
• Take electrostatic-discharge (ESD) precautions when handling the circuit board
• Verify the part number on the old unit matches before installation

The Sound Shield is an OEM replacement part for Whirlpool washers. It is a sheet metal panel installed behind the tub that helps reduce noise and vibration during spin cycles. With absorptive insulation, the sound shield dampens noise produced internally. 

Symptoms of a damaged sound shield include:

• Excessively loud operation, especially during high-speed spins
• Rattles, clanks, or resonant noises from inside the washer  
• Potentially weakened structure allowing tub movement
• Causes of a damaged sound shield can include tears or dents sustained over many high-speed spin cycles. Constant vibration may cause stress cracks or loose rivets.

 It is also compatible with some  Whirlpool, Maytag, Amana, and Kenmore brands.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

The Coin Drop Assembly is an OEM replacement part for Whirlpool washers. It allows users to insert coins and activate the machine on commercial or coin-operated washers.

A bad coin drop assembly can be caused by wear and tear over time or damage due to excessive use or mishandling. If you notice issues such as the coin mechanism not working, coins getting stuck, or the machine not starting when coins are inserted, it may be time to replace the coin drop assembly.

Symptoms of a faulty coin drop assembly include:

• Coins not being accepted or not registering
• Coins getting jammed or stuck in the mechanism
• Inability to start the washer with the coin insertion

Restore the function of your Whirlpool commercial washer by replacing the old or damaged coin drop assembly with this genuine OEM part.

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower wiring harness connects the washer's VMax2.0 control to lower electrical components, routing power and signals to the drain pump and other lower assemblies to help restore reliable pump operation and reduce intermittent electrical faults. What it does:

• Routes power and control signals between the VMax2.0 control system and lower/wet components, including the drain pump.
• Replaces damaged, pinched, or corroded wiring that can prevent the pump or lower assemblies from receiving power.
• Commonly used when the washer won't drain, the pump is unresponsive, or lower electrical components show intermittent faults.
• Matches OEM connector shapes and routing to maintain proper electrical connections and component function.

• Always disconnect power (unplug or switch off breaker) before accessing internal wiring.
• Inspect connectors and wiring routing for corrosion, bare wires, or chafing; secure harness away from moving parts and sharp edges.
• Match connector orientations during reassembly; ensure all clips and retainers are fastened to prevent strain on terminals.

Color: Grey

This stator is the stationary motor assembly that creates the magnetic field to drive the washer motor. It restores proper motor function so the washer can agitate and spin reliably when the rotor and drive are working. What it does:

• Generates the magnetic field needed for the washer motor to turn the rotor and tub
• Replaces a worn or damaged stator that can cause humming, no-spin, no-agitate, or intermittent motor operation
• Works with the rotor and motor assembly to deliver consistent torque during wash and spin cycles
• Designed to fit the original motor housing and align with factory mounting points

• One stator assembly

• High-level replacement only; motor disassembly is required—refer to manufacturer instructions or a service manual
• Disconnect power before servicing to avoid shock or injury
• Inspect rotor, bearings, and wiring while motor is accessible; replace any damaged components

Color: White

The Wire Harness is an OEM replacement part for Whirlpool washing machines. It is a crucial component that acts as the electrical wiring system, connecting various components and allowing them to communicate and transfer power effectively.

Symptoms of a bad Wire Harness include:

• Washer not powering on or receiving electricity
• Specific components or functions not working correctly
• Error codes or warning lights displayed on the control panel
• Burning smell or visible signs of electrical damage

Causes of a bad wire harness can include physical damage from impact or pinching, exposure to moisture or water, electrical surges or shorts, and general wear and tear over time. Faulty wiring can lead to connectivity issues and disrupt the proper operation of the washer's systems.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.