Mvwb85owq1 Parts

This is the control knob assembly for the appliance's control shaft. It lets you select settings by turning the shaft without tools. A worn or cracked knob can slip, spin freely, or make it hard to set temperatures or cycles.

• Rotates the control shaft to adjust settings
• Replaces knobs that are cracked, stripped, or hard to turn
• Helps restore precise selection of temperatures and cycles
• Common symptoms include a loose knob, no response when turning, or difficulty gripping

• Disconnect power and allow hot surfaces to cool before service
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the new knob with the shaft flat and press firmly until seated
• Test operation through the full range of settings

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Right side hinge.

This detergent dispenser assembly stores detergent and releases it at the right point in the wash cycle. Replace it to restore reliable soap dispensing and consistent cleaning when the cup door or mechanism fails.

• Holds detergent securely until the cycle calls for release
• Opens the detergent cup at the proper time for effective washing
• Helps prevent premature detergent loss and residue on dishes/clothes
• Common symptoms: soap door won't latch/open, detergent left in cup after cycle, visible cracks or leaks around the dispenser area

• Disconnect power and shut off water before service
• Access the dispenser at its mounting location; remove fasteners/release tabs and unplug the harness
• Seat the new assembly evenly on a clean surface to ensure a good seal; reconnect wiring
• Reassemble and run a test cycle to check for leaks

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This recirculation pump assembly drives water through the appliance's circulation system, maintaining steady flow and pressure for proper operation. Replace it if water won't circulate, performance drops, or the unit becomes noisy or shows a pump-related error.

• Moves water through internal channels to maintain consistent circulation and pressure
• Helps ensure effective cleaning/operation during wash or circulation steps
• Common failure symptoms: no/weak water movement, poor results, humming or grinding noises
• Trigger pump/circulation error messages or cause cycles to stall

• Disconnect power and shut off water supply before servicing
• Access is typically from the bottom/front; remove toe-kick or lower panels as needed
• Expect residual water; protect the area and transfer clamps/fittings from the old pump if required
• Seat any seals properly, reconnect hoses/wiring securely, and test for leaks and proper circulation

Color: White

The Top is an OEM part for Whirlpool washing machines. It forms the outer top shell of the washer, providing structure and housing for internal components. The top protects suspension rods, drive motor, controls and other parts while maintaining an attractive aesthetic appearance. It is constructed from durable materials designed to withstand the mechanical stresses of the wash cycle.

Causes of a bad top can include wear and tear from years of operation, damage due to excessive shock or impact, or stresses from overloading the washer drum.

Symptoms of a bad top include:

• Cracking or splitting of the durable plastic material
• Loosening or coming detached from the washer cabinet over time
• Warping, bending or denting that compromises the structural integrity

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

Suspension rod ball and bushing kit includes 4 balls and 4 bushings.

The Wire Harness is an OEM part for Whirlpool washing machines. The wire harness is responsible for transmitting electrical signals that power components and allow them to communicate during each cycle.

Causes of a bad wire harness can be normal wear and tear over time, pinched or cut wires, or wire insulation breakdown due to heat or moisture exposure.

Symptoms of a bad wire harness include:

• Lights or display not working properly
• Washer not starting cycles
• Sensors or switches malfunctioning
• Intermittent operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This low-profile washplate mounts at the bottom of the tub to circulate water and roll laundry during the wash cycle. Replacing a stripped, loose, or cracked plate restores proper wash action and cleaning performance. What it does:

• Mounts to the drive shaft splines to create wash action and move water.
• Turns and lifts laundry for proper turnover and cleaning efficiency.
• Can address grinding/clicking during wash or wobble caused by broken fins.

• Includes: 1 washplate

• Disconnect power and water before servicing.
• Remove the center cap/cover to access the hold-down bolt; remove the bolt and lift off the old washplate. A puller may be needed if the plate is seized.
• Align the new plate with the shaft splines, press it fully down, reinstall the bolt and cap, and run a test cycle.

The Drawer is an OEM part for Whirlpool washers. It is a convenient part that holds and dispenses detergent and fabric softener during the wash cycle. This dispenser drawer ensures proper distribution of laundry soaps, allowing for effective cleaning and fabric care. It features compartments for different types of detergents, making it easy to add the right amount of each product.

Symptoms of a faulty dispenser drawer include:

• Leaking or dripping from the drawer area
• Difficulty in opening or closing the drawer
• Improper or inconsistent dispensing of detergents

A bad dispenser drawer can occur due to regular use, buildup of residue or clogs, or accidental damage. If you notice issues such as leaks, difficulty in opening or closing the drawer, or improper dispensing of detergents, it may be time to replace the dispenser drawer.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Color: White