Mvwc00xw3 Parts

This tub ring mounts at the top of the outer tub to contain splashes and suds during agitation and spin, helping prevent over-the-rim leaks. Replace a cracked or broken ring to restore proper water containment and fit.

• Acts as the upper splash shield for the outer tub
• Helps keep wash water and suds from escaping during operation
• Secures with locking tabs for a tight, even fit around the tub opening
• Typical signs of failure: cracks, broken/missing tabs, water or suds at the top of the tub

• Disconnect power and water; wear gloves and eye protection
• Lift or remove the top/console to access the tub opening
• Release retaining clips/tabs, remove the old ring, and clean the tub rim
• Align and snap the new ring evenly into place; confirm all tabs are fully seated before reassembly

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

The Inner Tub Ring Assembly is an OEM part for Whirlpool washers. This assembly serves as a protective barrier between the inner tub and the outer tub, providing support and stability during the washing process.

A bad inner tub ring assembly can be caused by damage, wear and tear, or improper installation. If you notice excessive movement or wobbling of the inner tub, water leakage, or unusual noises during the wash cycle, it may indicate a problem with the inner tub ring assembly.

Symptoms of a bad inner tub ring assembly include:

• Excessive movement or wobbling of the inner tub during operation
• Water leakage from the area where the inner tub and outer tub meet
• Unusual noises during the wash cycle
• Visible cracks or damage on the inner tub ring assembly

Replace your faulty inner tub ring assembly with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Washplate is an OEM part for Whirlpool washers. Located inside the washer tub, the washplate works together with the basket to agitate clothes during wash cycles. 

Causes of a bad washplate can include cracks, mineral deposits that clog holes, or excessive wear over time.

Symptoms of a bad washplate include:

• Inefficient or ineffective agitation of clothes
• Long wash times even on light soil levels
• Standing water in the bottom of the tub after spins
• Reduced water pressure during fill cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Agitator is an OEM part for Whirlpool top load washing machines. As the central agitating component, it plays a pivotal role by tumbling clothes up and down through wash water.  

Causes of a bad agitator can include bearing seizing from lack of lubrication, broken hub components leading to off-balanced movement, or worn gears and spacers reducing power transmission.

Symptoms of a bad agitator include:

• Incomplete or ineffective removal of stains and soil
• Noticeable vibrations and noise from the agitator area
• Damaged retaining parts allowing assembly to wobble
• Failure of the agitator to rotate or turn freely during cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Lid is an OEM replacement part for Whirlpool washing machines. It is the top cover of the washer that provides access to the interior drum and tub, allowing you to load and unload laundry. The lid is designed to be durable and secure, ensuring safe and proper operation of the washing machine.

Symptoms of a bad Lid include:

• Difficulty opening or closing the lid
• Lid not closing or latching properly
• Visible cracks or damage to the lid material
• Lid becoming detached or falling off

Causes of a bad lid can range from physical damage due to impact or mishandling, to wear and tear over time from repeated use. Exposure to excessive moisture or humidity can also contribute to the degradation of the lid material or mounting mechanisms.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.

The Sound Shield is an OEM replacement part for Whirlpool washers. It is a sheet metal panel installed behind the tub that helps reduce noise and vibration during spin cycles. With absorptive insulation, the sound shield dampens noise produced internally. 

Symptoms of a damaged sound shield include:

• Excessively loud operation, especially during high-speed spins
• Rattles, clanks, or resonant noises from inside the washer  
• Potentially weakened structure allowing tub movement
• Causes of a damaged sound shield can include tears or dents sustained over many high-speed spin cycles. Constant vibration may cause stress cracks or loose rivets.

 It is also compatible with some  Whirlpool, Maytag, Amana, and Kenmore brands.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

Replacement drive belt that transfers motor power to the appliance drum, restoring proper rotation and load movement. Replacing a worn or broken belt can stop slipping, prevent overheating, and return normal spin or tumble action. What it does:

• Transfers motor torque to the drum so the appliance can tumble or spin.
• Replaces cracked, glazed, frayed, or slipped belts that no longer grip properly.
• Common symptoms addressed: drum won't turn, intermittent spinning, loud squeal or rubbing noise, or a burning rubber smell.
• Helps restore normal cycle operation when the belt is the failure point.

• Includes: 1 replacement belt.

• Disconnect power (and gas supply for gas dryers) before starting any repair.
• Access varies by model — remove the correct panels or drum per the model-specific service manual.
• Inspect idler pulley, motor shaft, and drum grooves; replace worn components to prevent premature belt failure.
• Ensure the belt is routed and seated correctly on pulleys and perform a short test run after reassembly.

This screw is a genuine replacement fastener used to secure appliance panels and components for a reliable fit. It restores proper fastening where original screws are missing, stripped, or damaged. What it does:

• Fastens panels, trim, brackets or small components to keep parts aligned and secure
• Replaces missing or damaged screws that can cause loose panels or rattling
• Restores proper clamping force to prevent movement and wear on adjacent parts
• Matches OEM function and fit when the correct part number is used

• Disconnect power and water before servicing the appliance
• Use the correct driver to engage the head cleanly and avoid stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic

This rubber pad cushions and protects appliance components from vibration and abrasion, reducing noise and wear. It's a small replacement part that restores proper contact and dampening where original pads have worn or fallen off. What it does

• Cushions panels or components to reduce vibration and rattling
• Prevents direct metal-to-metal contact that can cause scratching or wear
• Helps stabilize parts that have shifted due to a missing or damaged pad
• Commonly replaced when noisy operation or visible pad deterioration occurs

• One replacement pad

• Disconnect power before accessing interior panels or components
• Remove any retaining clips or panels that block the pad's location; pad typically presses into place
• Verify orientation and seating against the mating surface; replace any worn fasteners or retainers
• If adhesive was used on the original, use an OEM-recommended adhesive only.

This is an inner tub that is used in many models of washing machines. The appliance has two tubs and the inner one is the component that holds clothing through washing cycles. It has an agitator in the middle and perforated sides so that the water can leave the tub when it spins. It's inside the outer tub, which seals in the water and is bolted to the washer body. The tub can be damaged or wear out and will need to be replaced.When replacing the inner tub in a washing machine, make sure the appliance is powered off and the water supply is disconnected. The process requires tools including a nut drive, a flathead screwdriver, a socket and extension, a hammer, and a spanner wrench. Remove the original damaged inner tub from the machine before installing the new one in its place. Reinstall other components before turning back on the power and water.The inner tub is sold as a single component. It is a genuine OEM replacement part that is directly sourced from the manufacturer. This part is made to be used with washing machines manufactured by Crosley, Whirlpool, Maytag, and Kenmore.

This replacement wire harness connects and routes electrical signals between components so your appliance can operate safely and reliably. It restores proper wiring paths and helps resolve intermittent power or control issues. What it does

• Re-establishes factory wiring connections between control components and powered parts
• Restores signal and power flow to eliminate intermittent operation or non-responsive controls
• Replaces damaged, frayed, or burned wiring that can cause shorts or electrical faults
• Helps prevent arcing and improves electrical reliability when installed correctly

• Disconnect power before inspecting or replacing the harness to avoid shock or damage.
• Verify routing and connector orientation match the original harness; secure with existing clips or ties.
• Inspect mating connectors and terminals; replace or repair any that are corroded or damaged.