Pdt525ssj0ss Parts

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The LED control board is an OEM part for GE dishwashers featuring electronic touch controls. It includes the display screen assembly that provides a visual interface during cycles.

Causes of failure can include cracks or damaged connectors from repeated door opening/closing stresses. Moisture exposure can exacerbate typical wear over time.

Symptoms of a malfunctioning display assembly include:

• Glitchy or frozen statuses that don't update properly
• Dead pixels or full screen failure making input impossible
• Fault codes that cannot be cleared
• Improper diagnostic readings hampering repair

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This tub insulation is the replacement foam/fiber wrap that lines the dryer drum area to help retain heat, reduce exterior cabinet temperature, and dampen operation noise for more efficient, quieter drying. What it does:

• Wraps around the dryer drum/tub to help limit heat loss during cycles
• Helps reduce cabinet surface temperature for safer operation
• Dampens vibration and operating noise from the rotating drum
• Supports consistent drying performance by improving heat retention
• Useful when original insulation is damaged, torn, or missing

• Disconnect power (and gas supply for gas dryers) before servicing
• Access requires removing the dryer cabinet or drum per OEM instructions
• Handle carefully—use gloves and eye protection; avoid breathing any loose fibers
• Reinstall with original fasteners and seal as needed to maintain drum clearance

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

The Lower Rack Assembly is an OEM component specifically designed for GE dishwashers. It provides shelving to organize dishes in the bottom zone for optimal cleaning. Subject to mechanical stresses and chemical wear over time, the plastic and metal parts that make up the lower rack can weaken. 

Causes of a bad lower rack assembly include cracks, breaks, or deformations from years of use and daily loading/unloading of dishes. 

Symptoms of a bad lower rack include: 

• Sagging or loose shelving that no longer keeps dishes organized and supported
• Missing or broken features like prongs or tabs used to hold stemware in place   

Replace yours today with this genuine GE OEM part to restore full functionality. Proper rack support is important for cleaning performance. This GE replacement part is compatible with some Hotpoint, RCA, and Kenmore models.

The Sump Overmold Service Kit is an OEM part for GE dishwashers. It includes the sump and filter assembly that collects food debris and drains water at the bottom of the dishwasher. This over-molded, tightly-sealed design removes soils and prevents leaks. 

Causes of failure can be cracks, chips, or splits to the sump overmold due to excessive mineral buildup, high heat, or other wear over time. Foreign objects entering the sump area may also damage the filter mesh.

Symptoms of a faulty sump over mold assembly include:

• Standing water at the bottom of the dishwasher  
• Water leaks during or after the cycle
• Poor draining or poor rinsing performance
• Grime or food debris stuck to dishes

This genuine GE part is compatible also with Hotpoint, RCA, and select Kenmore brands.

This Roller and Bracket Assembly is an OEM part for GE dishwashers. It is an essential component in the dishwasher's rack system, providing smooth and stable movement for the racks as they slide in and out. This assembly includes both the rollers and the brackets that attach them to the dishwasher racks, ensuring effortless gliding and reliable support. 

The need to replace the roller and bracket assembly can arise from wear and tear, damage, or misalignment. 

Symptoms of a faulty Roller and Bracket Assembly include:

• Difficulty in sliding the racks in and out smoothly.
• Racks getting stuck or derailing during movement.
• Noticeable wear or damage to the rollers or brackets.
• Unusual noises when moving the dishwasher racks.
• Loosening or detachment of the assembly from the racks.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This conduit seal fits the dishwasher's water-feed conduit connection, keeping wash water contained and pressure steady to the spray arms. Replacing a worn seal helps address leaks and maintain reliable cleaning performance.

• Seals the joint where the dishwasher's water feed conduit/tube connects within the wash system
• Helps prevent water leaks at the conduit connection point
• Maintains proper wash pressure for consistent spray performance
• Common signs of failure: drips beneath the unit, visible cracks/flattening, or a loose-fitting old seal

• Disconnect power and shut off the water supply before servicing
• Access the conduit connection (location varies by model), remove the old seal, and clean mating surfaces
• Lightly moisten the new seal to ease installation and seat it fully
• Reassemble and run a brief cycle to check for leaks

The Door Latch is an OEM part for GE dishwashers. It plays an integral role in securing the dishwasher door safely closed during operation, providing a proper seal for optimal cleaning and drying.

Causes of a bad Door Latch can include wear and tear of latch components from repeated usage, damage due to excessive force on the door, or moisture penetration resulting in latch malfunction. 

Symptoms of a bad Door Latch include:

• The door not latching fully or remaining partially open  
• Leaks or spray around door seal area during washing
• The door disengaging or popping open during cycles
• Error messages related to door closure or latching 

Replace yours today with this genuine OEM GE part to ensure your dishes are safely washed behind a securely closed and sealed door. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Variable Speed Pump Kit is an OEM replacement part for GE dishwashers. It contains the wash impeller and circulating pump that work together to spray water and recirculate water-detergent mixtures throughout cycles. 

Causes of failure include wear and tear on bearings/seals, mineral buildup on impeller assemblies, or compromised motor functionality preventing proper water flow adjustment.

Symptoms of a bad variable speed pump kit include:

• Inadequate or inconsistent water pressure   
• Doused or unsaturated dishes  
• Inability to adjust water volume for efficiency
• Flood or overflow errors requiring maintenance

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: This wash pump has the hidden heater integrated into the pump.

This dishwasher turbidity sensor assembly monitors water clarity in the sump and reports to the control so it can adjust wash time and rinses for optimal cleaning. Replacing a failed sensor can restore normal cycle decisions and performance.

• Measures wash-water clarity (soil/turbidity) and sends data to the control
• Helps optimize cycle length, number of rinses, and water usage
• A faulty sensor may cause unusually long or short cycles
• Can contribute to poor cleaning or failure to complete a cycle
• May set a sensor-related code in diagnostics on some models

• Disconnect power at the breaker and shut off water before servicing
• Access from the bottom/front of the dishwasher; place a towel to catch residual water
• Unplug the wire connector, rotate the sensor to unlock, and remove; ensure the seal seats properly when installing the new part
• After installation, check for leaks and run a test cycle

This middle spray arm conduit assembly restores proper water delivery to the dishwasher's middle level. It channels wash water to the mid arm and rotates to improve coverage on the upper rack for consistent, reliable cleaning.

• Routes water from the pump to the middle spray arm to wash items on the upper rack
• Spins and sprays through jet holes for even coverage
• Replaces cracked, warped, or clogged assemblies that hinder rotation or spray
• Typical symptoms include poor cleaning on the upper rack, the mid arm not spinning, or visible damage/clogs

• Disconnect power and water supply before servicing
• Pull out the upper rack; release the rear coupling/retainer and any tabs or clips to remove the old assembly
• Fully seat the new assembly into the rear water supply port; ensure the spray arm spins freely
• Run a short test cycle to check for leaks

The Upper Spray Arm Support is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper spray arm, and is responsible for securely mounting and holding the upper spray arm in place during operation.

Symptoms of a bad upper spray arm support include:

• Vibration or noise from an unsecured spray arm
• Improper alignment of water spray pattern  
•  Restricted rotation of the spray arm during washing
• Leaks at the tub connection point

Causes of a bad spray arm support can be from cracks or breaks that compromise its structure, or wear over extended use without replacement. 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This wash pump kit is the dishwasher's circulation pump assembly that pressurizes and recirculates water through the spray arms. Replacing a failing pump restores wash pressure, cleaning performance, and helps eliminate leaks or loud humming/grinding from the sump area.

• Recirculates wash water under pressure to drive the spray arms
• Maintains steady water flow through the wash system and filters
• Typical symptoms: poor cleaning or no spray, loud humming/rumbling or grinding, leaks at the pump area, or cycles that stall/stop
• Use when the circulation system is weak, seized, or noisy

• Disconnect power and shut off water supply before servicing; allow components to cool
• Bail out any standing water and place towels to catch residual water
• Pull the dishwasher to access the sump/pump area as required by your model; carefully disconnect hoses and wiring
• Ensure seals seat evenly and clamps are secure; run a short test cycle and check for leaks before final reinstallation

This dishwasher fill hose routes incoming water from the inlet valve into the tub. Replacing a brittle or leaking hose helps restore proper filling and reduces the risk of water leaks under the unit.

• Carries fresh water from the inlet valve to the dishwasher during the fill cycle
• Helps maintain correct water level for reliable wash performance
• Common symptoms of a failed hose: leaks near the toe kick, slow fill, or no fill
• Replaces hoses that are cracked, swollen, kinked, or deteriorated

• Disconnect power and shut off the water supply before service
• Place a towel or shallow pan to catch residual water
• Access behind the lower kick panel; transfer existing clamps/fittings as needed
• Route the hose without kinks, fully seat connections, restore water, and check for leaks during a test cycle