Pdw 7800J10bb Parts

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This is the display/control circuit board for the refrigerator's user interface. It drives the temperature/readout display and processes button inputs so you can adjust settings and dispenser functions from the front panel.

• Manages the front-panel display and keypad signals
• Helps when the display is blank or dim
• Helps when buttons don't respond or settings won't change
• Helps with erratic or incorrect temperature readouts

• Disconnect power to the refrigerator before servicing
• Use proper ESD precautions when handling the board
• Take photos of wire/ribbon connections to ensure correct reassembly
• After installation, restore power and verify display and button operation

Size: 10-32 GXTT FLP.595 S

This microfilter sits in the dishwasher sump to capture fine food particles so water recirculates cleanly. Replacing a torn or clogged filter can help restore wash performance and protect the pump and spray arms from debris.

• Screens out fine debris to keep recirculating wash water cleaner
• Helps prevent redepositing and spray-arm clogs
• Common signs include gritty residue on dishes, poor cleaning results, visible tears/warping, or a filter that won't lock securely

• Disconnect power at the breaker before servicing.
• Open the door and remove the lower rack.
• Twist to unlock and lift out the old filter; clear any debris from the sump (locking direction varies by model).
• Seat the new filter fully and rotate to lock; ensure it's flush and secure.

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

This condenser fan motor circulates air across the refrigerator condenser to help remove heat and support efficient cooling. Replacing a faulty motor restores proper condenser airflow and can prevent temperature rise and compressor overwork. What it does:

• Spins the condenser fan to draw air across condenser coils, aiding heat dissipation
• Helps the compressor run efficiently by preventing condenser overheating
• Common symptoms of failure: refrigerator or freezer running warm, motor not running, humming, or loud/abnormal fan noise
• Can cause longer run cycles and higher energy use when airflow is restricted or stopped

• Disconnect power to the appliance before starting any repair
• Handle the fan blade and condenser fins carefully to avoid damage
• Verify wiring and mounting locations match the original; secure all connectors and fasteners

The GE screw is an OEM replacement part responsible for securing various components and parts of the dishwasher together. The screw is designed to provide a tight and secure connection for different panels, brackets, or other elements within the dishwasher. It plays a crucial role in maintaining the structural integrity of the appliance by preventing loose parts.

Common causes of a bad screw can include regular wear and tear from frequent use, exposure to moisture leading to corrosion, or damage from over-tightening. A compromised screw can result in loose or unstable components, which can affect the dishwasher's performance and safety.

Symptoms of a bad screw include:

• Loose or wobbly components within the dishwasher
• Difficulty in securing parts properly
• Visible rust or corrosion on the screw
• The screw head being stripped or damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This sump gasket seals the dishwasher's sump to the tub to keep wash water contained. Replacing a worn or flattened gasket helps stop leaks and maintain proper wash and circulation performance.

• Creates a watertight seal between the sump/pump assembly and the tub bottom
• Helps prevent leaks onto the floor or into the base pan
• Maintains wash pressure and circulation by preventing air intrusion
• Replace if torn, cracked, deformed, or if water is leaking from the center/bottom of the unit

• Disconnect power and water before servicing; use gloves to protect from sharp edges
• Access the sump from inside the tub or underside (model dependent); remove spray arm/filter as needed and release the retaining ring or tabs
• Clean mating surfaces; install the new gasket evenly without twists and ensure proper orientation
• Reassemble and run a brief fill/wash to check for leaks before fully reinstalling

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly