Pdw7800goocc Parts

This suction ring sits in the dishwasher's sump/filter area and helps channel wash water into the circulation system. Replacing a worn ring can help restore proper water pickup and spray pressure for reliable cleaning performance.

• Helps maintain suction at the pump inlet for steady water flow to the wash system
• Supports proper spray arm rotation and wash coverage
• Common symptoms of failure: poor cleaning, weak spray, spray arms not turning consistently, or unusual noise from the sump area
• Wear or damage can disrupt circulation

• Disconnect power and water supply before servicing
• Remove the lower rack, then the lower spray arm and filter/sump cover to access the ring
• Note the ring's orientation; press the new ring fully into place before reassembly
• Run a short test cycle to ensure proper circulation

Size: 10-32GX FLT25 .615 S

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

Size: 10-16 ab.

Vent driver assembly operates the dryer vent door to manage airflow during operation. Replacing a faulty driver restores proper vent door movement, improving exhaust flow and helping prevent backdrafts. What it does:

• Moves and positions the vent/duct door so exhaust can exit when the appliance runs
• Retracts/closes the vent door when the appliance stops to limit backdrafts
• Common symptoms: vent door won't open or close, reduced exhaust airflow, or visible vent door sticking
• Interfaces with the vent door linkage and the appliance wiring harness to receive control signals

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Basic hand tools are typically required; support the vent door assembly during removal/installation
• Handle wiring connectors and plastic components carefully to avoid damage
• Follow the appliance's service manual or OEM instructions for exact steps and torque/spec guidance

This clamp secures a hose or small tubing connection on compatible GE laundry appliances to help prevent leaks and keep the connection stable during operation. Durable metal construction resists vibration and wear. What it does:

• Holds a hose or tube firmly to a fitting to reduce leaks and loss of water or airflow
• Stops hose slippage caused by vibration or pressure changes
• Helps restore a tight connection after hose replacement or service
• Simple, low-profile design for use in confined appliance spaces

• Disconnect power and shut off water supply before servicing
• Drain hoses and remove remaining water to avoid spills
• Use the proper screwdriver or nut driver to tighten; do not over-tighten
• Inspect the hose and fitting for wear and replace if damaged before reinstalling the clamp

This mechanism assembly is the timed control component that advances and governs cycle functions, restoring proper cycle sequencing and timing for the appliance. It replaces a worn or non-advancing timer mechanism. What it does:

• Advances the appliance timer so cycles progress to the next step
• Controls mechanical switch cams that engage heating, agitation, or spin
• Commonly helps when cycles won't advance, stop mid-cycle, or run continuously
• Works as the core drive for mechanical timer-based controls

• Disconnect power before servicing to avoid shock or injury
• Handle gently; align cams and shafts as OEM instructions specify
• Refer to the appliance's service manual or tech sheet for exact alignment and testing procedures

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

Size: 8-18 B 1HW 1/2 S N

Size: 8-18 x 7/8 inch.

The Middle Spray Arm Kit is an OEM replacement part specific to GE dishwashers. It contains the rotating center arm component that helps distribute water, dishwasher detergent, and moisture across the middle rack shelves for enhanced cleaning.

Causes of a bad middle spray arm can include clogged spray holes inhibiting proper water coverage, worn ball bearings reducing spray force, or broken or missing spray arm attachment clips.

Symptoms of a bad middle spray arm include:

• Items on middle racks not receiving sufficient cleaning
• Dried food or soap scum buildup is visible on rack shelves and dishes
• The arm fails to rotate or spin during cycles
• Detached spray arm is no longer connected to the dishwasher tub

This OEM GE replacement is compatible with many GE, Hotpoint, and Profile dishwasher models.

The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.

Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.

Symptoms of a bad Fine Filter Hub Nut include:

• Poor cleaning results with food particles left on dishes
• Unusual noises during the wash cycle
• The filter becoming loose or not staying in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.