Pdw880j033ss Parts

This dishwasher vent cover mounts on the inner door and shields the exhaust opening. It directs moist air out during drying while helping keep spray and debris out of the vent path to protect internal components. What it does:

• Covers the door vent opening and helps guide exhaust airflow during the dry cycle
• Helps keep water spray and debris from entering the vent assembly
• Supports proper moisture management around the top of the door/control area
• Replace if the cover is cracked, warped, loose, or missing, or if steam/water escapes from the vent area

• 1 vent cover

• Disconnect power at the breaker and turn off the water supply; wear cut-resistant gloves
• Access is through the door; on many models the inner door panel must be removed to reach the vent area
• Ensure any gasket/seal is properly seated and secure the cover evenly—do not overtighten
• Run a short cycle and inspect the vent area for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This float dome sits in the dishwasher's float well and rises with the water level to trigger the float switch and stop filling. Replace a cracked or missing dome to restore reliable water-level control and overfill protection.

• Moves up and down with the water level to actuate the overfill/flood switch
• Helps prevent overfilling by signaling the inlet valve to shut off at the correct level
• Guides and shields the float mechanism from dishes and debris
• Common symptoms: broken or missing dome, float sticking, dishwasher won't fill or keeps filling

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float area on the tub floor
• Lift straight up or twist to remove the old dome; clear any mineral/debris from the float well
• Seat the new dome and run a brief fill test

This water inlet cover replaces a cracked or missing inlet-valve trim to protect and conceal the appliance's water inlet area. It restores a finished look while keeping hoses and valve components shielded from debris. What it does:

• Covers and protects the water inlet valve and hose connections from dust and impact
• Conceals exposed hoses and wiring for a cleaner rear-cabinet appearance
• Helps prevent snagging or accidental contact with the inlet valve assembly
• Reduces debris buildup around the inlet area that can affect connections

• Disconnect power to the appliance and shut off the water supply before starting.
• Usually fastens with a few screws or clips—have a screwdriver or nut driver ready.
• Align cover over the inlet valve area, then secure with the original fasteners.
• After installation, turn water and power back on and inspect connections for leaks.

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Right hand side

This electronic control module assembly manages the dryer's cycle selection, timing and user interface so the dryer runs the selected program reliably. Replaces a failed control board to restore normal operation and controls. What it does

• Receives user inputs and starts selected dryer cycles
• Controls cycle timing, motor and heating signals per program
• Communicates status to the display and keypads/buttons
• Common symptom link: dryer won't start, won't advance cycles, shows control/display errors, or has intermittent operation

• Disconnect power before service to avoid shock—this is an electrical assembly.
• Handle the board by the edges and avoid static discharge; use proper ESD precautions if available.
• Verify harness connections and mounting before powering up; do not force connectors.

This inner door panel replaces a damaged or worn internal door surface to restore a clean, secure oven/microwave door interior and support proper window assembly alignment. It fits behind the outer door and holds the inner glass in place. What it does:

• Replaces cracked, chipped, or warped inner door surface that can trap debris or affect door closure
• Restores the inner layer that helps keep the door assembly aligned and stable
• Reduces rattling or vibration caused by a loose or broken inner panel
• Helps maintain a clean interior appearance by covering internal components

• Disconnect power (and gas, if applicable) and allow the appliance to cool before starting
• Handle the panel carefully—sharp edges or glass may be exposed; wear gloves and eye protection
• Keep all original fasteners and note screw locations
• After installation, confirm the door closes and seals correctly and test the appliance on a short cycle

Right hand side

Specs: 10-32 gxtt flp.59

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

Left hand side