Pdwt180vooss Parts

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

This left-hand arm hinge assembly replaces a worn or damaged door hinge to restore proper door alignment and smooth opening and closing. Designed as the left-side support arm for the appliance door. What it does:

• Supports the left side of the door and secures the door to the cabinet during operation
• Guides smooth door movement and helps prevent sagging or uneven closing
• Stops rubbing, binding, or intermittent contact that can cause noise or poor seal
• Restores proper door fit to maintain normal operation and safety

• Disconnect power to the appliance before starting any repair
• Support the door while removing and installing the hinge to prevent dropping
• Use basic hand tools; verify hinge orientation and alignment before tightening
• Retain or replace mounting hardware if damaged; do not overtighten fasteners

Size: 8-18 B 1HW 1/2 S N

This water injector fill hose connects the household water supply to the refrigerator's water/ice system, restoring reliable water flow for dispensing and ice production. Designed as a direct replacement to restore proper fill operation. What it does:

• Delivers water from the inlet to the ice maker/water dispenser assembly.
• Restores proper water fill for ice production and dispenser use when the hose is damaged or leaking.
• Helps stop leaks, sputtering dispensers, or slow/irregular ice fill caused by cracked or blocked tubing.
• Works with the refrigerator's injector/fill pathway to maintain consistent water delivery.

• One water injector fill hose.

• Disconnect power and shut off the water supply before installing.
• Inspect and replace any worn clamps or connectors; tighten fittings to prevent leaks.
• Avoid kinking the hose; route it following the original path to prevent flow restriction.

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This pump motor hanger is the support bracket that secures the washer pump motor to the appliance frame, helping keep the motor stable during operation for reliable drainage performance. What it does:

• Holds the pump motor in the correct position to prevent vibration and misalignment
• Maintains pump-to-housing alignment so the drain pump can move water effectively
• Helps reduce unusual noise or movement caused by a loose motor mount
• Fits where the motor attaches to the washer chassis; replaces worn or bent hangers

• Disconnect power before starting any repair and follow basic electrical safety
• Basic hand tools required; keep original fasteners unless damaged
• Inspect pump and motor for wear while replacing the hanger

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This dishwasher vent cover mounts on the inner door and shields the exhaust opening. It directs moist air out during drying while helping keep spray and debris out of the vent path to protect internal components. What it does:

• Covers the door vent opening and helps guide exhaust airflow during the dry cycle
• Helps keep water spray and debris from entering the vent assembly
• Supports proper moisture management around the top of the door/control area
• Replace if the cover is cracked, warped, loose, or missing, or if steam/water escapes from the vent area

• 1 vent cover

• Disconnect power at the breaker and turn off the water supply; wear cut-resistant gloves
• Access is through the door; on many models the inner door panel must be removed to reach the vent area
• Ensure any gasket/seal is properly seated and secure the cover evenly—do not overtighten
• Run a short cycle and inspect the vent area for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This float dome sits in the dishwasher's float well and rises with the water level to trigger the float switch and stop filling. Replace a cracked or missing dome to restore reliable water-level control and overfill protection.

• Moves up and down with the water level to actuate the overfill/flood switch
• Helps prevent overfilling by signaling the inlet valve to shut off at the correct level
• Guides and shields the float mechanism from dishes and debris
• Common symptoms: broken or missing dome, float sticking, dishwasher won't fill or keeps filling

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float area on the tub floor
• Lift straight up or twist to remove the old dome; clear any mineral/debris from the float well
• Seat the new dome and run a brief fill test

This water inlet cover replaces a cracked or missing inlet-valve trim to protect and conceal the appliance's water inlet area. It restores a finished look while keeping hoses and valve components shielded from debris. What it does:

• Covers and protects the water inlet valve and hose connections from dust and impact
• Conceals exposed hoses and wiring for a cleaner rear-cabinet appearance
• Helps prevent snagging or accidental contact with the inlet valve assembly
• Reduces debris buildup around the inlet area that can affect connections

• Disconnect power to the appliance and shut off the water supply before starting.
• Usually fastens with a few screws or clips—have a screwdriver or nut driver ready.
• Align cover over the inlet valve area, then secure with the original fasteners.
• After installation, turn water and power back on and inspect connections for leaks.