Pfcs1jwa Ss Parts

This refrigerator temperature control board regulates cooling by reading sensor inputs and directing the compressor, fans, and defrost cycle. Replacing a failed board helps restore accurate temperatures and responsive controls.

• Monitors temperature sensors and maintains set points
• Controls the compressor, fans, and defrost cycle as designed
• Interfaces with the temperature buttons/display where equipped
• A failing board can cause drifting temps or no cooling, unresponsive controls, or intermittent cycling

• Disconnect power before servicing and verify no voltage is present
• Use ESD protection; handle the board by the edges only
• Photograph wiring; move keyed connectors one at a time and seat fully
• After installation, restore power and allow up to 24 hours for temperatures to stabilize; follow any model-specific setup on the service sheet

Restore a reliable door seal with this refrigerator door gasket. It forms an airtight barrier between the door and cabinet to keep cold air in, reduce frost and condensation, and help your unit maintain stable temperatures.

• Seals the full door perimeter to prevent warm, humid air from entering the compartment
• Helps maintain consistent cooling performance and moisture control
• A worn, torn, or deformed gasket may cause temperature swings, frost/ice buildup, or moisture around the door
• Visible gaps, a door that won't stay closed, or a failed "paper test" indicate a failed seal

• Unplug the appliance before starting
• Let the new gasket relax flat; gently warm with a hair dryer on low or place in warm water to remove kinks
• Fully seat the gasket lip into the door channel/retainer, working evenly around all four sides and corners
• After installation, check the seal with a paper strip and fine-tune by gently warming and reshaping as needed

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

This is a control board for refrigerators. The control board governs the main functions of the appliance, such as cooling and defrosting.The most prevalent sign of a damaged control board is the noticeable elevation of the temperature inside the refrigerator compartments. The refrigerator may also stop defrosting properly, which can lead to leaking and other issues with the appliance. Begin the installation by unplugging the refrigerator from its main power source. Locate the control board panel on the back-right corner of the appliance. Remove the housing screws and slide the access panel off. Unplug the wires to the control board and remove the mounting screws. Repeat these steps in reverse to install the new control board.This control board is a genuine OEM product sourced directly from the manufacturer. The control board is only available individually and does not include any other components. This product is compatible with GE appliances.

Restore a tight seal and stable temperatures with this refrigerator door gasket. Replacing a worn gasket helps keep cold air in and humid air out to reduce frost, condensation, and unnecessary energy use.

• Forms an airtight seal around the door perimeter
• Helps maintain consistent temperature and humidity
• Reduces frost/ice buildup and interior condensation
• Can address doors that won't close fully or pop open
• Replace if torn, brittle, warped, or not sealing evenly

• Disconnect power before servicing
• Let the gasket warm to room temperature; use warm water or low heat to relax folds
• Remove the old gasket and press the new gasket into the retainer, seating corners first
• Check for even contact all around; adjust door/hinges as needed for a proper seal

The Water Filter Housing and Tube Assembly is an OEM part for GE refrigerators. This assembly is responsible for securely holding the water filter in place while directing water through the filter and into the dispenser or ice maker. Approximate dimensions: 18" x 14.7" x 3.3"

Over time, the water filter housing and tube assembly can become damaged due to regular use, exposure to high water pressure, or mineral deposits building up inside the tubes. Such damage may lead to leaks or reduced water flow, affecting the performance of the refrigerator's water and ice systems.

Symptoms of a faulty water filter housing and tube assembly include:

• Water leaks around the filter area
• Low water flow to the dispenser or ice maker
• Difficulty installing or removing the water filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This blower fan duct channels air moved by the evaporator fan through the refrigerator's air passages, helping maintain consistent temperatures and reliable cooling performance. Replacing a cracked or warped duct restores the designed airflow path and reduces fan noise. What it does:

• Directs airflow from the evaporator fan to the cooling vents for proper circulation
• Helps balance temperatures between compartments for even cooling
• A damaged or misaligned duct can cause weak airflow, warm spots, frost/ice around the cover, or unusual fan noise
• Restores correct air routing after breakage or warping

• Disconnect power before servicing to avoid electrical shock or moving-fan injury
• Remove shelves/drawers and the interior cover as needed to access the duct; retain screws and clips
• Transfer any reusable seals or hardware from the original duct to the new part
• After reassembly, ensure the fan spins freely and no rubbing noises are present before returning to service

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

This refrigerator ice maker assembly freezes water and automatically ejects cubes into the bin. Replacing a failed unit restores steady, hands-free ice production and helps resolve common ice maker cycling and cube-ejection issues.

• Freezes water in its mold, then harvests and drops finished cubes into the ice bin
• Controls fill and harvest timing for consistent cube production
• Typical failure symptoms: no ice production, unit stuck mid-cycle, cubes not ejecting, or loud clicking/grinding from the drive
• Works with the refrigerator's controls to pause ice making when the bin is full

• Disconnect power and shut off the water supply before servicing
• Remove the ice bin and any covers; unmount the old ice maker and disconnect its wiring harness
• Transfer any brackets, covers, or guides from the old unit if needed
• Mount the new assembly, reconnect wiring, restore power/water, and allow up to 24 hours for full ice production

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This fan and pre-wired harness assembly drives airflow to the Quick Chill/CustomCool drawer so foods and beverages chill faster and hold the set temperature. Replace a noisy, non-running, or intermittent fan to restore proper drawer cooling.

• Circulates cold air into the Quick Chill/CustomCool/deli drawer for targeted cooling
• Helps correct no-chill or slow-chill performance in the drawer
• Addresses symptoms like no airflow, intermittent operation, or grinding/buzzing noises from the drawer area
• Replaces a failed fan motor or damaged wiring harness in this assembly

• Disconnect power before servicing; remove the drawer and covers to access the assembly
• Note wire routing and connector locations; transfer any original mounting hardware as needed
• Seat connectors fully and route harness away from moving parts to avoid pinching
• Restore power and verify the fan runs and airflow is present to the drawer

Front mounting grommet.