Pgb911eejes Parts

This is a replacement screw used to secure appliance panels and small components. It restores proper fastening and helps eliminate loose parts, rattling, or misaligned panels for a tight, safe fit. What it does:

• Secures panels, trim, brackets, or small assemblies to restore proper alignment
• Stops rattling or vibration caused by missing or loose fasteners
• Provides the correct threaded fastening where the original screw is lost or damaged
• Matches OEM fastening function for reliable reassembly

• Disconnect power or unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread the screw in by hand first, then tighten snugly—do not overtighten to avoid stripping or cracking
• Keep small parts away from children and pets during installation

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

This glow-bar oven igniter lights the gas burner. When energized, it heats and draws current through the safety valve so the bake or broil flame ignites reliably and the oven reaches the set temperature. What it does:

• Heats and ignites the oven's bake or broil burner
• Draws the correct current to open the gas safety valve
• Can address no-heat or no-ignition conditions
• Helps resolve very slow preheat or inconsistent oven temperatures
• Useful when the igniter glows but the burner never lights

• 1 glow-bar igniter

• Disconnect power and shut off gas supply before servicing
• Access from the oven cavity; remove racks, oven bottom, and flame spreader as needed
• Handle the igniter carefully—element is fragile; avoid touching the carbide/ceramic tip
• Secure connections and route wires away from flames and high-heat areas; test operation after reassembly

The Orifice Holder is an OEM part for GE gas ranges. It secures the orifice spud in place, maintaining proper alignment of gas ports to burner tubes.  

The orifice holder prevents any movement or misalignment of gas passages, ensuring uninterrupted and precise fuel delivery. Correct positioning is critical for safe, efficient combustion and optimal heat levels.

Causes of a faulty holder can include wear and tear, damage from impact or heat exposure, or loose fasteners allowing misalignment over time.

Symptoms of a bad orifice holder include:

• Unstable or uneven burner flames  
• Inability to adjust oven temperature as needed
• Gas leaks near burner area
• Abnormal burner combustion noises

Replacing with this genuine OEM GE part restores secure orifice placement and optimized gas flow. It is also compatible with Hotpoint, KitchenAid, and select Kenmore gas range models.
 

This surface burner valve regulates gas flow to a single cooktop burner for smooth, precise flame control. Replacing a worn valve can restore reliable ignition and adjustment on the affected burner while maintaining safe operation.

• Regulates and meters gas from the manifold to one surface burner
• Works with the control knob to provide simmer-to-high flame settings
• Common failure symptoms include: burner won't ignite, weak or unstable flame, gas odor near the knob/valve area, or a knob that is hard to turn
• Labeled "270" per GE specification to match the correct valve style/position used in select models

• Disconnect power and shut off the gas supply before servicing
• Access the manifold; note the valve's position and orientation before removal
• Reassemble and check all connections for leaks using an approved leak-detection solution
• If the burner still won't light, also inspect the burner orifice, igniter, and spark system

This oven light gasket fits between the glass lens and the oven liner. It restores a proper seal around the light opening to help keep grease and moisture out of the light cavity and hold the lens securely in place. What it does:

• Seals the joint between the oven light lens and the cavity wall
• Helps prevent grease and moisture from entering the light assembly
• Keeps the lens snug to reduce looseness or rattling
• Replace if the gasket is cracked, flattened, brittle, missing, or if moisture/grease is visible around the lens

• One oven light lens gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/retainer as your model requires (unscrew lens or release clips)
• Note gasket orientation and clean the mating surfaces
• Seat the new gasket evenly and reinstall the lens; do not overtighten the glass

The Convection Motor is an OEM part for GE gas ranges. It is the component responsible for circulating hot air around food inside the oven cavity during convection cooking cycles. 

Causes of a bad convection motor include failed windings, worn bearings, or damage from excess heat over time.

Symptoms of a bad convection motor include:

• Inability to select convection cooking functions 
• Lack of air movement inside the oven
• Slower than normal cooking times 
• Uneven baking or roasting results

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Automatic Latch is an OEM part for GE gas ranges. It is a component of the stove door that automatically secures the door shut when closed.  

Causes of a bad automatic latch include wear and tear from continuous use over many years. The latch mechanism is subjected to repeated opening and closing of the heavy stove door. Exposure to cooking heat and grease build-up can also degrade plastic and metal parts.

Symptoms of a bad automatic latch include:

• The door not securely latching on its own when closed  
• Gaps appearing around the sealed door perimeter
• Loose, gritty movement of the latch mechanisms
• Manual help needed to fully close and lock the door

This part is also compatible with some Hotpoint and RCA gas range models.

This stainless steel oven door handle gives your range a finished look and a safe, sturdy grip for opening and closing the oven. It replaces a damaged, loose, or missing handle to restore normal operation and appearance. What it does

• Provides a secure handhold for opening and closing the oven door.
• Replaces handles that are bent, dented, cracked, or have stripped mounting holes.
• Stops wobble or play from loose or damaged handles when tightened or replaced.
• Restores the appliance's appearance with a stainless steel finish.

• One stainless steel oven door handle

• Disconnect power to the appliance before beginning work; allow the oven to cool completely.
• Support the oven door when removing or installing the handle to prevent dropping or pinching.
• Use the correct fasteners and hand tools; tighten mounting screws securely but avoid over-torquing.

This oven door gasket assembly seals the oven door to help keep heat, smoke and odors inside the oven cavity for more even cooking and improved efficiency. It replaces a worn or damaged door seal quickly and easily. What it does:

• Forms a heat-tight seal around the oven door to reduce heat loss and improve temperature stability
• Helps prevent smoke and odors from escaping into the kitchen
• Reduces energy waste from a failing or brittle seal
• Common symptom fix: visible gaps, charred or compressed gasket, heat felt at the door edge, longer cook times or uneven baking

• One oven door gasket assembly

• Disconnect power (and gas if applicable) and allow the oven to cool completely before beginning
• Inspect the door and retainer for damage; remove old gasket per OEM instructions and fit new gasket evenly into the retainer channel
• Avoid over-stretching the gasket; ensure a continuous seal around the full perimeter

This small replacement bumper cushions and protects the appliance frame/trim where panels meet, helping reduce vibration, chipping and rattles for a cleaner, quieter fit. Ideal when the original bumper is worn, cracked or missing. What it does:

• Cushions contact between the frame/trim and adjacent panels to reduce noise and prevent damage
• Helps maintain proper panel alignment and sealing where the trim meets the cabinet
• Reduces rattling or vibration caused by loose or degraded trim pads
• Restores protective spacing that prevents chips or scratches to finished surfaces

• One frame front bumper

• Disconnect power to the appliance before starting work and follow all safety precautions
• Usually installs by pressing into a slot or onto a mounting surface after removing the trim piece; some trim removal may be required
• Inspect mating surfaces for damage or debris and clean before installing the new bumper
• Replace with the exact part number only; do not force or modify the bumper to fit

This orifice holder secures the gas orifice in the burner tube to ensure stable fuel delivery for consistent burner flames. It replaces a worn or damaged holder to restore correct orifice alignment and flame performance. What it does

• Holds the gas orifice in proper position inside the burner tube for accurate fuel flow
• Helps maintain consistent, even burner flames and reliable ignition
• Common replacement when burners show weak, uneven, or inconsistent flames
• Works with the stove's burner assembly to prevent orifice dislodgement during use

• One orifice holder

• Turn off the range's gas supply and unplug the appliance before starting work
• Remove burner grates and caps, then detach the burner tube to access the holder
• Inspect the orifice and surrounding components; replace the orifice if damaged