Pse26kgebww Parts

This replacement trim fits the dairy compartment on the refrigerator door. It restores a clean, finished look and proper fit of the butter/dairy bin so contents stay organized and the area opens and closes smoothly.

• Attaches to the front edge of the dairy/butter bin on the fresh food door to provide a finished, secure fit
• Replaces cracked, warped, or missing trim that can cause gaps, rattling, or a loose dairy compartment
• Helps keep small items from sliding out when opening/closing the door
• Built to match the original mounting points for straightforward replacement

• Disconnect power to the refrigerator before servicing
• Open the fresh food door; release tabs or remove any retaining screws to take off the old trim
• Align the new trim with the mounting points and snap in or reinstall existing hardware
• Handle plastic tabs carefully and avoid overtightening screws

This authentic OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's essential functions, such as adjusting and maintaining temperature. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced. To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and unscrew the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This dispenser paddle assembly is the lever you press inside the refrigerator's ice/water dispenser. It actuates the dispenser switch for ice or water and replaces a damaged or worn lever to restore smooth, responsive dispensing.

• Transfers your push to the dispenser switch to start water or ice flow
• Provides a solid, responsive contact surface in the dispenser recess
• Can help when the dispenser won't activate or only works when pressed very hard
• Addresses a cracked, loose, sticking, or slow-to-return paddle

• Disconnect power and turn off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access mounting screws; avoid breaking tabs
• Note switch orientation and wiring; transfer any reusable hardware from the original part if needed
• Reassemble, restore power/water, and test for proper activation and return

Arc handle assembly replaces a broken or worn refrigerator door handle, restoring a secure, ergonomic grip and clean appearance. Designed as a direct replacement to return normal door access and everyday usability. What it does:

• Replaces cracked, chipped or separated door handles so the door can be opened safely and comfortably.
• Restores proper grip and lever action for normal door operation and user access.
• Helps stop wobbling or loose-hanging handles that can snag or feel unsafe.
• Matches factory-style mounting points for a tidy, like-new appearance.

• High-level replacement; basic hand tools (screwdriver) are typically required. Keep original screws and trim for re-use when possible.
• Support the door while removing/installing the handle to avoid pinching or damage.

This refrigerator meat pan front cover forms the visible front edge of the deli/meat drawer assembly, helping contain items and providing a clean finished look so the drawer opens and closes smoothly.

• Provides the front trim/face of the meat (deli) drawer cover assembly
• Helps keep contents contained and aligned in the drawer
• If cracked, loose, or missing, the drawer may not slide or seal properly
• Cosmetic damage or broken tabs are common signs this part needs replacement

• Unplug the refrigerator before servicing
• Remove the deli/meat drawer to access the cover area
• Handle any glass in the shelf assembly carefully to avoid breakage
• Align tabs and snap/slide the new cover into place without forcing

This bottom hinge pin supports and serves as the pivot for the refrigerator door. An accurate, tight-fitting hinge pin helps the door swing smoothly and seal properly to maintain temperature and reduce wear.

• Serves as the lower pivot point for the door on the bottom hinge
• Helps keep the door aligned for proper closing and gasket contact
• Replacing a worn pin can improve door movement and reduce stress on the hinge

• Unplug the appliance before servicing
• Support the door to relieve weight from the hinge before removing hardware
• Transfer any spacers/shims in their original order to maintain alignment
• Tighten fasteners securely and check door swing and seal after installation

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

The Paddle Assembly is an OEM replacement part for GE refrigerators. It is responsible for controlling the flow of water or ice from the dispenser, allowing you to dispense water or ice.

A bad dispenser lever paddle assembly can occur due to regular use or accidental damage. If you notice symptoms such as difficulty in pressing the lever, inconsistent water or ice flow, or the lever not returning to its original position, it may indicate a need to replace this part.

Symptoms of a bad dispenser lever paddle assembly include:

• Difficulty in pressing the lever
• Inconsistent water or ice flow
• Lever not returning to its original position

Restore your refrigerator by replacing the faulty dispenser lever paddle assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Fresh food side. For the same part in black, purchase WR11X10009.

Freezer side.

This electronic board powers and controls the light at the refrigerator's water/ice dispenser. Replacing it restores reliable illumination and proper on/off operation so you can clearly see the dispenser area during everyday use.

• Supplies regulated power to the dispenser light circuit for consistent brightness
• Responds to dispenser/control inputs to turn the light on and off
• A failing board can cause flickering or dim lighting
• Common symptoms include no dispenser light, intermittent light, or a light that stays on

• Disconnect power to the refrigerator before servicing
• Access the board behind the dispenser panel/escutcheon; remove trim carefully to avoid damage
• Handle the board by the edges and avoid static discharge; ensure connectors are fully seated

This manufacturer-specified screw fastens appliance panels, brackets, and internal components in place. Replace a missing or stripped fastener to restore a tight, rattle-free fit and reliable support at the original mounting points.

• Provides the correct fastener for securing covers, brackets, and assemblies
• Replaces lost, rusted, or damaged screws
• Helps resolve loose or vibrating panels and trim
• Maintains alignment of components and hardware

• Unplug the appliance; shut off water if working near supply lines
• Match the new screw to the original location; verify length and thread
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Keep removed hardware organized for reassembly

Includes 12 retainer rings.

This hex-head screw secures refrigerator components where a 12-24 x 7/8 in fastener is specified. Replacing a missing, stripped, or rusted screw restores a tight, reliable fit for brackets, panels, and assemblies and helps eliminate vibration and rattles.

• Fastens panels, brackets, and other assemblies in the refrigerator at locations calling for this size hardware
• Replaces worn, stripped, or missing screws to restore secure mounting
• Helps correct loose or misaligned components and reduce vibration noise
• OEM size: 12-24 thread, 7/8 in length; hex head

• Disconnect power and, if applicable, shut off the water supply before service
• Match the screw to the original location; replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use an appropriate nut driver or socket that fits the hex head

This shelf support replaces a broken or missing bracket that holds a refrigerator shelf in place. Restore a level, secure shelf surface and stop sagging or unexpected drops with a simple, like-for-like replacement.

• Supports the edge of an interior shelf and keeps it level
• Locks the shelf into the cabinet/liner mounting point
• Common signs to replace: shelf sags or tilts, won't stay positioned, support is cracked, loose, or missing
• Helps prevent shelf movement that can lead to spills

• Disconnect power and remove items from the affected shelf before starting.
• Note the position and orientation of the old support to match placement.
• Snap or screw the new support into the existing mounting point; transfer any reusable hardware.
• Reinstall the shelf and verify it seats level and secure.