Pseed Queen Parts

This capacitor sleeve kit insulates and protects the refrigerator's capacitor. Replacing a cracked or missing sleeve helps prevent chafing or contact with metal surfaces and wiring, supporting safe, reliable operation of the capacitor and nearby components.

• Provides electrical insulation to help prevent shorts if the capacitor contacts metal surfaces
• Adds abrasion protection and cushions the capacitor against vibration
• Restores proper fit/routing when the original sleeve is brittle, melted, or missing
• Common indications include exposed capacitor body or leads and visible rubbing marks on the old sleeve

• Disconnect power before servicing; wear gloves and eye protection
• Discharge the capacitor per service procedures before handling
• Note factory orientation/routing; slide the sleeve over the capacitor and position to clear sharp edges
• Re-secure the capacitor in its bracket/harness and verify clearance before restoring power

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

This replacement knob fits the temperature control on the refrigerator's chill/deli/snack pan. It restores your ability to adjust airflow to the drawer so you can set the pan to a colder or warmer setting when the original knob is broken or missing. What it does:

• Attaches to the chill/deli pan temperature control to regulate cold-air flow into the drawer
• Restores user control of the drawer's colder/warmer setting
• Typical symptoms include a cracked or missing knob, a knob that won't stay on, or slipping/stripped engagement
• May help if the drawer setting can't be adjusted because the knob is damaged

• 1 control knob

• Unplug the refrigerator before servicing
• Remove the deli/snack pan for access to the control shaft
• Align the knob with the shaft and press on firmly until fully seated
• Reinstall the pan and restore power; verify the control turns smoothly

This condenser fan mounting bracket secures the condenser fan motor and blade in the correct position to move air across the coils. Replacing a cracked or bent bracket restores stable mounting, reduces vibration, and helps maintain proper condenser airflow.

• Holds the condenser fan motor/blade assembly in alignment for proper airflow through the condenser
• Maintains clearance to prevent the fan blade from rubbing or contacting nearby components
• Helps reduce rattling, vibration, or scraping noises from the rear of the refrigerator
• Damage or misalignment can contribute to restricted condenser airflow and warmer temperatures

• Disconnect power and pull the refrigerator away from the wall to access the rear service area
• Remove the rear lower access panel; note wiring and hardware locations
• Support the fan motor/blade while removing the old bracket; transfer motor, blade, grommets, and screws to the new bracket
• The fan spins freely with proper clearance and correct airflow direction before reassembly

This 3-way triple water valve controls water flow to the dispenser and ice maker on compatible refrigerators, restoring proper water delivery and preventing leaks when the valve fails. It replaces a worn or stuck valve assembly. What it does:

• Directs water to the ice maker, fresh-food dispenser and/or water filtration line as the refrigerator requests
• Opens and closes electrically to allow water flow when the dispenser or ice maker calls for water
• Common symptoms: no water to dispenser or ice maker, slow flow, intermittent flow, or active leaking at the valve
• Works with the refrigerator's inlet hose and internal water lines to route water where needed

• One triple (3-way) water valve assembly

• Turn off water supply and unplug the appliance before starting; relieve system pressure by running the dispenser briefly after shutoff
• Handle water lines and fittings carefully to avoid damage
• Tighten hose connections securely and check for leaks after restoring water and power

Fresh food side. Color: white. For the same part in black, purchase WR02X10779.

The Main Board is an OEM part for GE refrigerators. Located inside the refrigerator's back wall, it acts as the central processing unit controlling all cooling, defrosting, and appliance functions. Reliable performance relies on a functioning main board.

Causes of failure can involve moisture exposure corroding electronic chip pathways over time, failed solder joints inhibiting connections to other boards, or extreme power surges damaging circuitry. 

Symptoms of a defective main board are:  

• Refusal to turn cool or respond to temperature settings
• Abnormal or lack of ice production  
• Failure of lights, fans, and other features to engage

Replacing with this genuine GE main board restores complete refrigeration and feature operation. Compatible with Hotpoint, RCA, and select Kenmore refrigerators as well, it ensures long-term dependable service.
 

This grille base is the lower front kick grille that restores the refrigerator's finished look and helps direct airflow at the appliance base. It replaces a cracked, broken, or missing lower grille for a secure fit and neat appearance. What it does:

• Covers and protects the refrigerator's lower front area and internal components from debris.
• Helps channel airflow across condenser/vent openings to maintain proper ventilation.
• Replaces damaged or broken grille pieces that can cause rattling or poor fit.
• Restores the appliance's finished look by replacing warped or discolored trim.

• Disconnect power to the appliance before beginning any service.
• Handle edges carefully; align clips/tabs with mating slots for a secure fit.
• Some models use snap-in tabs or screws—retain hardware and reattach in the original locations.
• If tabs or mounting points are broken, inspect surrounding trim for additional damage.

This replacement screw secures refrigerator panels, brackets, and trim to help keep components aligned and quiet. It matches the specified #8-18 thread and 1-1/2 inch length used at designated mounting points.

• Fastens panels, brackets, covers, and hardware as designed by the manufacturer
• Restores a missing or damaged fastener to keep parts secure and aligned
• Correct #8-18 tapping thread and 1-1/2 in. length for specified locations

• Unplug the refrigerator or disconnect power before servicing
• Wear cut-resistant gloves to protect from sharp edges
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any model-specific washers or clips originally installed on your unit

This replacement gasket seals the evaporator cover to the cabinet, preventing air leaks and directing airflow where it belongs. Restores a tight seal to help minimize frost buildup and temperature swings for more consistent cooling performance.

• Seals the perimeter of the evaporator cover to prevent air bypass and warm-air infiltration
• Helps maintain proper airflow through the evaporator and air ducts
• Can reduce frost/ice on or around the rear panel and air outlets
• Improve and stabilize refrigerator/freezer temperatures when the original gasket is torn, compressed, or missing

• Disconnect power to the refrigerator and wear cut-resistant gloves
• Remove shelves/bins and the evaporator cover; retain screws/clips
• Remove the old gasket and clean mating surfaces; seat the new gasket evenly without gaps or twists
• Reinstall the cover and restore power and verify no air leaks

The Harness Cab Lower is an OEM replacement part for GE refrigerators. It sits behind the fresh food doors and contains wiring harnesses that power critical interior features.

Causes of a bad harness cab can include damaged insulation exposing wire fraying, breaks or crimps in wiring preventing power delivery, or short-circuits due to moisture over time. 

Symptoms include: 

• Lights, dispensers, or other interior components ceasing to operate properly
• Error codes or failure indications on control panels
• Buzzing or humming noises from wiring when functions are used

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This cover pan assembly is the molded drain tray that routes defrost and condensation water to the refrigerator drain, helping keep the cabinet base dry and protecting internal components from moisture damage. What it does:

• Collects and channels defrost/condensation water into the drain system to prevent pooling
• Protects compressor and electrical components from water exposure
• Helps reduce musty odors and water stains caused by leaks under the cabinet
• Restores proper water flow if a cracked or warped pan was causing spills

• One cover pan assembly as shown

• Disconnect power to the appliance before beginning any work
• Access may require removing the rear or lower front kick plate depending on model
• Handle plastic mounting tabs carefully to avoid breakage; replace any damaged clips
• Inspect and clear the drain tube and trough while installing to ensure proper flow

This dial installs on the refrigerator chill/pan control to let you set the compartment temperature. Replacing a broken or loose dial restores proper control and makes adjusting the chill drawer quick and reliable. What it does:

• Rotates on the chill/pan control shaft to change the compartment temperature setting.
• Replaces worn, cracked, or missing dials that are hard to turn or don't stay set.
• Helps address inconsistent deli/drawer temperatures when the control dial fails.
• Matches the original OEM shape for correct fit and alignment on the control shaft.

• Always unplug the appliance or shut power to the refrigerator before servicing.
• Remove the drawer/pan or access panel as needed to reach the control shaft.
• Pull the old dial straight off the shaft and press the new dial onto the shaft until fully seated; avoid forcing at an angle.
• After installation, restore power and verify the dial turns smoothly and adjusts the compartment temperature setting.

This condenser assembly is the condenser coil used in compatible refrigerators to release heat from the refrigerant so the appliance can cool efficiently. Replacing a damaged coil helps restore proper cooling performance and energy use. What it does:

• Circulates refrigerant through the condenser coil to dissipate heat from the refrigeration system
• Supports normal compressor cycling and helps maintain steady internal temperatures
• Common symptom fixes: reduces long run times, improves inadequate or uneven cooling, and addresses overheating or noisy compressor operation
• Works with the condenser fan and other sealed-system components to complete the heat-exchange process

• Disconnect power to the refrigerator before servicing to avoid electric shock
• Access commonly from the rear lower panel or front grille; may require removal of kick plate or back cover
• Avoid damaging the coil fins; handle carefully and use fin comb if needed

This fastener secures appliance components where a #8-18 AB hex-washer-head screw is specified. At 1/2 inch long, it restores a tight, reliable hold when an original screw is missing, damaged, or stripped.

• Secures brackets, panels, and covers where this size/thread is specified
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration or rattling caused by loose fasteners
• Correct #8-18 AB thread and 1/2-in length for a precise fit

• Disconnect power before servicing; shut off water supply if working near water connections
• Compare to the original to confirm length and thread match
• Start threads by hand to prevent cross-threading; use the correct driver for the head type
• Tighten snugly; do not overtighten into plastic or thin sheet metal

• Thread: #8-18 (Type AB)
• Head: Hex-washer
• Length: 1/2 in

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.