Pts221cr Parts

This PTC start relay mounts on the refrigerator compressor and briefly energizes the start winding, then automatically opens as it warms. Replacing a weak relay helps restore reliable compressor starts and consistent cooling. What it does:

• Provides momentary power to the compressor's start winding at startup; the PTC element opens as it heats
• Helps ensure smooth compressor starts and reduces repeated start attempts
• Signs of a failed start device can include no cooling because the compressor won't run
• Clicking or buzzing from the compressor area every few minutes
• Compressor starts intermittently or stops shortly after starting

• Includes: 1 PTC start relay

• Disconnect power and pull the refrigerator forward to access the rear service area
• Remove the rear panel to reach the compressor compartment
• Unplug the wire harness and pull the old relay straight off the compressor terminals; note its orientation
• Push the new relay fully onto the compressor prongs, reconnect the harness, reinstall the panel, and restore power

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

The Motor Fan Assembly is an OEM part for GE refrigerators. This part circulates air throughout the refrigerator, ensuring consistent cooling and temperature regulation.  

Over time, the motor fan assembly can wear out or fail due to regular use, electrical issues, or physical damage.  

Symptoms of a bad motor fan assembly include:

• Unusual noises coming from the refrigerator, such as buzzing or humming
• The refrigerator or freezer not cooling properly
• Increased temperature fluctuations inside the refrigerator
• The refrigerator running continuously without cycling off

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the magnetic door gasket that seals the fresh food compartment, keeping cold air in and warm air out to maintain temperature and reduce frost and energy loss.

• Creates an airtight seal around the refrigerator (fresh food) door
• Helps maintain proper internal temperature and humidity
• Worn, torn, warped, or hardened gaskets can cause warm spots, sweating/condensation, or excessive run time
• Replace if the door won't seal, you see gaps/light around the door, or the gasket is cracked or misshapen

• Unplug the appliance before servicing
• Soften the new gasket in warm water or with gentle heat to improve flexibility
• Remove the old gasket from the door channel; press the new gasket fully into the groove, working evenly around the perimeter
• Check door alignment and perform a "paper test" to confirm a uniform seal

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or damaged seal helps restore proper temperature, reduce frost, and improve energy efficiency.

• Seals the freezer door perimeter to maintain set temperature and airflow
• Helps reduce frost/ice buildup and condensation around the door opening
• May help if you notice warm spots, frequent frost, the door not staying shut, or visible gasket tears/gaps
• Reduces warm air infiltration that can cause long run times and temperature swings

• Unplug the refrigerator before servicing
• Warm the new gasket in hot tap water or with a hair dryer on low to make it pliable; seat the corners first
• Depending on the model, either press the gasket into the retainer channel or loosen and retighten inner-liner screws to secure—do not overtighten
• After installation, check the seal all around (dollar-bill test); gently warm and reshape any areas with gaps

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This replacement clamp secures lines or components inside the refrigerator, keeping them properly routed and stable. Replacing a broken or missing clamp helps reduce vibration and prevents rubbing damage or leaks from loose tubing. What it does:

• Holds tubing or wiring harnesses securely in place inside the refrigerator
• Maintains correct routing and clearance to prevent chafing and wear
• Helps reduce vibration and rattling noises from unsecured lines
• Can help prevent drips or leaks when used to retain water tubing

• 1 clamp

• Unplug the refrigerator and, if working with water lines, shut off the water supply
• Note the original clamp orientation and routing; take a photo before removal
• Install the new clamp in the same location, securing lines without pinching or over-stressing them
• Restore power (and water if applicable) and check that lines are secure; inspect for leaks if used on water tubing

This fresh food door gasket creates an airtight seal around the refrigerator compartment door to prevent air leaks. Replacing a worn seal helps maintain stable temperatures, reduce moisture at the door, and restore proper closing and sealing.

• Creates a tight seal around the fresh food door to prevent air infiltration
• Helps maintain consistent temperatures and minimize condensation at the door
• Wear indicators include cracks, tears, warping, or visible gaps in the seal
• Common symptoms: door not sealing well, warm spots in the fridge, or longer run times

• Disconnect power before servicing
• Remove the old gasket and clean the door's gasket channel/retainer
• Warm the new gasket in clean warm water to relax folds; start at corners and press the lip fully into the channel without stretching
• Close the door and check for uniform contact; adjust hinges/strike if needed and allow up to 24 hours for the gasket to fully conform

This replacement screw secures panels, brackets, and other hardware in your appliance. Installing a new fastener restores a tight, rattle-free fit when the original is missing, stripped, or corroded, helping keep components properly aligned.

• Fastens components, trim, and brackets to the cabinet or frame
• Replaces a missing, stripped, or rusted screw
• Helps reduce rattles, vibration, and loose panels or handles
• Maintains proper alignment of panels and hardware

• Disconnect power (and water/gas if applicable) before servicing.
• 12-24 thread, approximately 0.90-inch length; match to the original location.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Replace any additional damaged fasteners to ensure even clamping and a secure fit.

This is the flexible perimeter seal for the freezer door. Replacing a worn gasket helps the door close snugly to keep cold air in and moisture out, supporting stable freezer temperatures and reducing frost at the door edge.

• Creates an airtight seal between the freezer door and cabinet
• Helps with symptoms like frost or moisture around the door opening
• Can address a door that won't seal, gaps at the corners, or a torn/hardened gasket
• Helps stabilize freezer temperature when the seal is compromised

• Disconnect power and clear items from the door
• Warm the new gasket in hot water to relax folds before installation
• If your model uses screws or a retainer, loosen as needed; remove the old gasket and press the new gasket fully into the groove, ensuring corners are seated
• Close the door and check for uniform contact all around; adjust hinges/leveling as needed and allow the gasket to conform over the next 24 hours