Sde 4606Ayw Parts

This terminal block assembly connects your dryer's power cord to the internal wiring, providing a secure, heat-resistant junction. Replacing a damaged block restores a reliable electrical connection and helps prevent intermittent power, overheating, or burnt terminals.

• Provides an insulated junction point between incoming power and the appliance's internal wiring
• Secures cord conductors with screw terminals to maintain a tight, low-resistance connection
• Helps resolve issues like the dryer not powering on, intermittent shutdowns, or a burning smell near the cord cover
• Replaces cracked, melted, or stripped terminals to restore a safe power path

• Disconnect power at the breaker before servicing
• Photograph/label wire positions and move one wire at a time to the new block
• Tighten terminal screws firmly; recheck connections after initial operation
• Inspect/replace any heat-damaged cord lugs, wiring, or strain relief before reassembly

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

Color: White. Measures about 3 inches in diameter.

The Dryer Timer Dial Skirt is an OEM part designed specifically for Whirlpool dryers. It acts as a protective and decorative cover around the timer dial, providing clear labeling for various dryer settings. 

Color: Bisque

Over time, the dial skirt may degrade due to frequent use, exposure to heat, and potential impact, leading to cracks, discoloration, or broken markings. These issues can make selecting the appropriate cycle difficult or confusing.

Signs that the Dryer Timer Dial Skirt may need replacing include:

• Faded or illegible cycle markings
• Cracks or broken sections on the skirt
• The dial skirt no longer fitting snugly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cycle selector knob is used on some Maytag washers and dryers. This is not the timer knob. Color: stainless steel. Measures about 2 inches in diameter where the handle extends.

Dryers, washers, and washer dryer combos are made with an idler pulley shaft. It works in combination with the rest of the equipment in multiple ways. It switches the direction in which the output shaft is rotating. The idler pulley shaft also works to change gears and maintain the space between shafts. With time, because of excessive force, or as a result of misuse, the idler pulley shaft can wear out, break, or get damaged otherwise. When the part isn't working correctly, it has to be replaced to continue using the machine.The primary indication that there is something wrong with the idler pulley shaft is a machine that's producing excessive noises. Replacement of the idler pulley shaft is a straightforward process. It can be done in a few minutes with a nut driver and screwdrivers. Unplug the appliance before starting the disassembly.This idler pulley shaft is a genuine OEM replacement part. It is sold as an individual unit. It is made of durable metal materials. The idler pulley shaft is sourced from the manufacturer. It can be installed in various machines made by Speed Queen, Amana, and Magic Chef.

This is the rotating dryer cylinder assembly. Replacing a dented, rusted, or out-of-round cylinder restores smooth tumbling and helps prevent snags, noise, and uneven drying performance.

• Holds and tumbles laundry while working with the belt/drive system
• Internal white baffles lift and separate clothes for better airflow
• Smooth interior helps protect fabrics from catching or tearing
• Typical signs it's needed: loose or broken baffles, interior rust, dents, scraping/thumping once per revolution, or recurring fabric snags

• Disconnect power; for gas dryers, also shut off the gas supply
• Wear cut-resistant gloves—metal edges can be sharp
• Access typically requires removing the top/front panels and releasing belt tension; note belt routing
• Set drum, route belt correctly, spin by hand to confirm clearance, then reassemble and test

Screw: 8-16 x 3/8 inch.

This selector knob attaches to the control shaft so you can choose cycles and options on your appliance. Replace a cracked or stripped knob to restore smooth, accurate settings without forcing or damaging the control stem.

• Attaches to the control shaft to operate the cycle/timer or option switch
• Common symptoms: knob is cracked, stripped, loose, spins freely, falls off, or is missing
• Restores positive, accurate control feel when selecting settings

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the keyed/flat side and press the new knob on until fully seated
• If your original knob used a spring clip or insert, transfer it to the new knob before installation

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This electronic timer controls dryer cycle selection and timing, restoring proper cycle advancement and user control. It replaces a failed or unresponsive timer to help your dryer start and run the selected cycles reliably. What it does

• Advances dryer cycles and manages timed and automatic cycle control.
• Provides the user interface signals for start/stop and cycle selection.
• Can correct symptoms like a dryer that won't advance through cycles, won't start reliably, or has an unresponsive cycle selector.
• Works with the dryer's control circuitry to coordinate motor and heater operation during selected cycles.

• Disconnect power to the dryer before any service to avoid shock risk.
• Verify wire connections and match terminal locations to the wiring diagram before removal.
• Handle the control carefully; avoid bending terminals or contaminants on connectors.

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

Size: 10-24 x 3/8 inch.

This coin drop mounts in the machine's coin area to accept and detect U.S. quarters, then signal a credit to start a cycle. Replace it if valid coins are rejected, credits don't register, or vending is intermittent.

• Accepts U.S. 25-cent coins and sends a credit signal to the control
• Guides the coin into the collection path/box after acceptance
• Helps resolve issues like valid quarters not accepted or credits not registering
• Symptoms can include intermittent crediting or machine not starting after inserting coins

• Disconnect power before servicing
• Access the coin/control area and note wiring and mounting orientation
• Move any reusable screws or bezels as needed; install the new drop securely
• Reconnect wiring and test operation with several quarters before returning to service