Shp65t52uc/09Uc/07 Parts

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Installation Set is an OEM component specifically designed for installing Bosch dishwashers. It contains mounting fittings and hardware required to securely attach your dishwasher into place beneath countertops or cabinetry. 

Symptoms of a faulty installation set can include coming loose from mounting surfaces over time or missing, damaged parts that inhibit proper attachment. Replacement ensures accurate install fit.

Causes of a bad installation set include wear and tear related to repeated load shifting, impact, or mishandling leading to broken brackets/screws, or missing pieces after DIY installation attempts.

Causes of a bad installation set include:  

• Vibrations or rocking motions during wash cycles
• Drainage or plumbing connection issues  
• Installation difficulties requiring replacement parts

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 
 

The Frame is an OEM part for Bosch dishwashers that provides support and organization for your cutlery, offering a designated space for your forks, knives, spoons, and other utensils. 

A bad frame can occur due to wear and tear, accidental damage, or exposure to harsh chemicals. Signs of a faulty frame include cracks, broken sections, or difficulty in smoothly sliding the drawer in and out.

Symptoms of a bad frame include:

• Cracks or broken sections in the frame 
• Difficulty in sliding the cutlery drawer in and out
• Unorganized or unstable storage of cutlery 

Replace your damaged or worn-out frame with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This push button set replaces worn or broken control-panel buttons to restore reliable manual control and a finished appearance. Designed for straightforward swap-in replacement on compatible Bosch appliances. What it does:

• Replaces damaged or missing push buttons on the control panel
• Restores tactile feedback and accurate button actuation
• Helps prevent unintended operation from stuck or cracked buttons
• Improves the appliance's cosmetic appearance at the user interface

• One push button set

• Disconnect power to the appliance before beginning any service
• Generally installs from the front of the control panel; some panels may require removing trim or access panels
• Handle plastic parts carefully to avoid breaking tabs or clips

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks

This insulating part installs in the specified location to help reduce heat transfer between internal spaces and exterior panels. Replacing a worn or missing insulator helps protect nearby components and maintain proper operating temperatures.

• Provides a thermal barrier to limit heat transfer to surrounding panels and wiring
• Helps prevent scorching or heat damage to adjacent components
• Restores proper insulation where the original has deteriorated or is missing
• Common signs of failure: visible damage or fraying, burnt odor, or unusually hot exterior areas

• Disconnect power and allow the appliance to cool completely before servicing
• Wear gloves and eye protection; insulation fibers can irritate skin and eyes
• Match the original orientation/placement; do not over-compress the material
• Keep insulation clear of vents, heating elements, fans, and moving parts

This trim strip finishes and protects the exposed edge of the appliance where it installs, helping secure adjacent panels and giving a clean, finished look. Replacing a damaged strip can improve fit and appearance.

• Provides a finished edge and helps secure panels or covers in place
• Helps prevent gaps that can collect debris
• Common fix when the existing strip is cracked, bent, loose, or missing
• Reduce rattles or vibrations caused by an ill-fitting trim piece

• Disconnect power and shut off any utilities before servicing
• Note orientation/position of the old strip before removal
• Press or fasten the new strip into the same mounting points; do not force
• After installation, recheck clearances and panel alignment

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability