Shxm78w52n/11 Parts

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Indicator Light is an OEM part for Bosch dishwashers. It serves as a visual cue, providing important status updates and notifications related to the dishwasher's operation.

Causes of a malfunctioning Indicator Light can stem from issues with the control board or wiring harness that powers the light, or the light itself burning out due to age or electrical surges.

Symptoms of a bad Indicator Light include:

• The light not illuminating at all, even when it should be on
• Flickering or dimming of the light during operation
• The wrong indicator light turning on or staying on inappropriately

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This replacement dishwasher door handle restores a secure, easy-to-grip place to open and close the door, improving usability and appearance. Designed to match the original fit and mounting style for straightforward swap-out. What it does:

• Replaces a cracked, bent, or missing door handle so the door can be opened and closed safely
• Provides a solid grip to prevent slips and reduce stress on the door panel
• Restores factory appearance when the original handle is damaged or worn
• Helps prevent further cabinet or door edge damage from makeshift grips

• Disconnect power to the appliance before starting any repair to avoid injury
• Many installations require removing the inner door panel to access mounting screws; keep hardware organized
• Use basic hand tools (screwdriver, nut driver) and avoid overtightening fasteners to prevent damage

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

The Door Handle is an OEM part for Bosch dishwashers. It provides a convenient and sturdy way to open and close the dishwasher door. The door handle is designed to withstand repeated use and provide a comfortable grip. It ensures that you can easily access the dishwasher's interior to load and unload your dishes.

A bad door handle can occur due to wear and tear, accidental damage, or improper installation. Signs of a faulty handle include a loose or wobbly grip, difficulty in opening or closing the door, or complete detachment from the dishwasher door.

Symptoms of a bad door handle include:

• Difficulty in fully opening or closing the door
• The handle detaching from the dishwasher
• Scratches, dents or discoloration 

Replace your damaged or worn-out dishwasher door handle with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks