Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement 8-32 x 5/8 mounting screw for securing internal panels, brackets, and components in stand mixers. Restores tight fit if original is missing or stripped.
I purchased a replacement assembly from Appliancepartspluspro.com Upon inspection of new part I noticed there were only 6 terminals for the 8 wires I needed to connect. After much investigation by their tech support person Ali, it became apparent that my old part was discontinued and no longer available. The new part was the correct replacement but now I had to figure out what to do with the 2 extra wires. I labeled all of the wires and the terminals on the the old part. After moving wires, one... Read more
Right-side crisper cover support mounts to the inner wall and holds up the crisper cover and glass. Replace if cracked, broken, or missing to restore level.
Freezer running too warm or too cold? This thermistor cover shields the temperature sensor for accurate cooling. Simple snap-in installation fixes misreads.
I am not a plumber, but very good with anything mechanical. I uninstalled the broken icemaker, swapped the wiring and ice bar from the old icemaker to the new one, and installed the new icemaker all in 12 minutes and 37 seconds from start to finish, which includes pulling out the two freezer baskets and pulling off the freezer door. This repair could not have been any simpler. Great product! Read more
Factory black screw that secures panels, trim, or brackets on your oven. Replace missing, stripped, or damaged fasteners to restore secure fit.
Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more
Replaces cracked or broken refrigerator light covers. Protects bulb and shields components from moisture. Slides into place with mounting tabs. Verify fit.
Replaced the cover Read more
Rear roller that helps move your refrigerator smoothly. Replace if broken, cracked, or wobbling to restore easy mobility. Confirm fit by model number.
Removed all the food from the freezer and most from the fridge before starting. Tipped fridge back until I could place a 2 x 4 a couple of inches behind the front rollers. With the front of the fridge now approximately 3 to 4" off the ground you can remove the adjusting bolt and the roller assembly can be pulled out of the brackets. Slide out of the notches where that hold it into the bracket. Same to install. Read more
Right-hand mounting adapter bracket secures end caps, trim, or shelf assemblies to your refrigerator cabinet wall. Replace if cracked, broken, or worn.
Secures covers, brackets, and internal panels in your refrigerator. Replace missing, stripped, or corroded screws to restore tight mounting.
I ordered the part from you which arrived much sooner than expected. I replaced the Rail-Mulln. It was so easy to fix, next time I'll let my wife do it. Read more
Mounting screw for refrigerator door handles. Secures handle to door panel. Replace if stripped, missing, or won't hold handle firmly in place.
Replaces worn oven door seals that allow heat to escape or show visible damage. Creates a tight barrier to maintain temperature and efficiency. Confirm fit.
Turned the power off. Lifted the oven door up and off.to make access easier and to clean an replace gasket.Then unscrewed the element brackets. Cleaned oven. Took oven door apart to replace gasket ,you have to separate the door halves to clean window and get the gasket out. This is where you better take pictures and notes. You need a large work bench and a good #2 Phillips. Taking the elements out you will deal with gouged out screws, rust stripped threads etc. You may need to buy some self... Read more
Protective seal grommet for hoses, tubes, or wires passing through refrigerator cabinet. Replaces cracked, worn, or missing grommets to prevent leaks.
Seals refrigerator or freezer door to prevent air leaks and maintain temperature. Replace if torn, deformed, or door won't close tightly. Confirm fit.
Left-hand adapter bracket secures freezer drawer rails in bottom-mount refrigerators. Replace if cracked, broken, or missing to restore proper alignment.
Washer won't fill or fills slowly? This water inlet valve controls hot and cold water flow. Common DIY fix takes about 20 minutes to install.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
Range indicator light assembly illuminates control panel displays. Replace when light fails or flickers. Verify fit with your model number.
Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.