Wbs571cihz01 Parts

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

This leveling leg threads into the base of your washer to set height and keep the cabinet stable on uneven floors. Replacing worn or missing legs reduces vibration, walking, and noise for smoother, safer operation.

• Provides an adjustable foot to level and support the washer
• Helps reduce vibration, rocking, and "walking" during spin
• Replaces stripped, cracked, or missing leveling feet
• Helps with excessive shaking, rattling noises, or out-of-balance conditions

• Disconnect power and water; pull the washer forward for access.
• Support the appliance to prevent tipping; unscrew the old leg by hand or with pliers.
• Thread the new leg into the base; adjust all feet until level front-to-back and side-to-side.
• Ensure each foot contacts the floor firmly and the cabinet is stable before use.

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

This mechanical timer replaces a worn or failing dial control to restore timed cycle sequencing and basic on/off switching. It helps your appliance run through its programmed cycles and regain reliable time-based control. What it does:

• Advances program steps and routes power to the appropriate components as cycles progress
• Commonly used where a rotating dial controls cycle timing and sequence
• Resolves symptoms like cycles that won't advance, controls that are unresponsive, or a dial that doesn't click or turn smoothly
• Re-establishes timed control when intermittent or non-functioning timing is caused by a faulty timer

• Disconnect electrical power to the appliance before starting any repair
• Take photos of wiring and connector positions before removal to ensure correct reassembly
• Handle the timer and its terminals carefully to avoid bending or damaging contacts
• Secure mounting hardware and verify proper operation through a complete cycle after installation

This tub assembly replaces a cracked or leaking wash tub to restore proper water containment and drum support for your washer, helping reduce leaks, rubbing noises, and abnormal vibration during cycles. What it does:

• Provides the sealed reservoir that holds wash water and supports the inner drum during wash and spin cycles
• Helps stop or reduce water leaks caused by cracked or damaged tubs
• Can resolve rubbing, scraping, or thumping noises from a warped or broken tub
• Helps stabilize the drum to reduce vibration and improve spin performance

• Disconnect power and shut off water supply before starting; wear gloves and eye protection
• Tub assemblies are heavy and bulky—use two people or appropriate lifting equipment
• Follow the washer OEM service manual for disassembly, seal transfer/replacement, and torque specifications
• If bearings, seals, or mounting hardware show wear, replace them per OEM guidance for a complete repair

Transmission drive pulley nut.

Includes 12 washers.

This power line filter sits between household AC and the washer's internal wiring to reduce electrical interference and help stabilize control operation. Replacing a failed filter may restore power and prevent nuisance breaker or GFCI trips.

• Filters incoming AC power to reduce electromagnetic interference reaching the control and motor circuits
• Helps prevent interference-related issues like erratic controls or random resets
• Failure may present as no power/blank display, intermittent power loss, or tripping a breaker/GFCI
• Visual clues of failure can include scorching, swelling, or a cracked housing

• Unplug the washer or switch off the circuit breaker before servicing; allow a few minutes for internal components to discharge
• Access the filter location (often near the control area or rear panel) per your model's service information
• Note wire locations (LINE, LOAD, and GROUND) and move one lead at a time to avoid miswiring
• Mount securely and ensure the ground connection to the cabinet is tight for proper operation

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Size: 14-10 a trt 7/8 s.

This 2-speed clutchless motor replaces the washer's drive motor to restore agitation and spin without a mechanical clutch. It provides the two common drive speeds used for agitate and spin cycles on compatible top-load washers. What it does:

• Turns the washer tub/agitation mechanism to enable agitate and spin functions
• Operates at two speeds (agitate and spin) using an internal clutchless design
• Commonly used when a washer hums, runs but won't agitate or spin, or fails to change between agitate and spin
• Works with the existing mounting bracket and wiring harness on compatible models

• Disconnect power before servicing to avoid shock or injury
• Motor is heavy and may require lifting assistance; support the tub during removal/installation
• Reuse the existing mounting hardware and wiring harness
• Follow the washer's service manual for disassembly, torque, and wiring routing; test operation before reassembling the cabinet

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

8-18 hi/lo 5/8

Size: 8-32 t. Includes 12 screws.

Size: 8-18 ab.

This hex nut overmold assembly secures appliance components while the molded sleeve protects surrounding surfaces and reduces vibration. It replaces worn or missing fasteners to restore a secure fit and help prevent rattling or movement. What it does:

• Provides a threaded fastening point for panels, trim, or internal brackets
• Molded overmold sleeve protects finishes and helps isolate vibration
• Restores secure mounting when a nut is stripped, missing, or loose
• Helps reduce rattling and movement of attached parts

• Disconnect power and follow appliance-specific safety procedures before starting
• Tighten by hand then snug with the appropriate wrench; avoid overtightening to prevent damaging the molded sleeve