Wed7ohebwo Parts

This drive motor powers the appliance's primary mechanical system. Replacing a weak or failed motor restores proper rotation and torque so cycles can complete without stalling, humming, or intermittent starts. What it does:

• Converts electrical power into rotational motion to drive the machine's mechanism
• Provides starting torque and sustained speed under load
• Helps resolve issues like humming with no movement, overheating/thermal cutout, or intermittent operation
• Addresses symptoms such as burning smell, excessive noise, or a shaft that won't turn freely

• One drive motor

• Disconnect power before servicing; allow any moving parts to stop completely
• Note and label wire locations; transfer connectors carefully to the new motor
• Support the assembly when removing mounting hardware to prevent drops or damage
• After mounting, verify the motor spins freely by hand and that connectors are fully seated before restoring power

Replacement refrigerator door hinge that restores proper door alignment and smooth pivot action. Swap a worn, bent, or broken hinge to help the door close fully and reduce rubbing, sagging, or seal gaps. What it does:

• Supports and pivots the refrigerator door, keeping it aligned with the cabinet.
• Replaces a bent, cracked, or worn hinge that can cause door sag or uneven gaps.
• Helps the door close more easily to maintain an effective seal and reduce cool-air loss.
• Reduces scraping or rubbing between the door and cabinet caused by misalignment.

• Disconnect power to the appliance or unplug it before starting work; remove food and shelves from the door if necessary.
• Support the door while removing and installing the hinge to prevent damage or injury.
• Use proper fasteners and tighten hardware securely but avoid over-torquing; check door alignment and make small adjustments as needed.

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

This seal sits between the dryer's blower housing and its cover to keep the air path tight. Replacing a crushed or torn seal helps restore proper airflow and drying performance while minimizing lint leakage inside the cabinet.

• Creates an airtight joint between the blower housing and cover
• Helps prevent air leaks that lead to longer dry times
• Helps keep lint contained within the exhaust path
• Replace if the original seal is torn, flattened, deteriorated, or missing

• Disconnect power; for gas models, shut off gas and allow the dryer to cool
• Access the blower housing (typically behind the lower front panel)
• Clean mating surfaces; install the new seal evenly around the perimeter with no gaps
• Reassemble and verify strong, unobstructed airflow at the exhaust

For mating terminal use [AP31136300].

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This control bezel is the front trim piece that surrounds and protects the appliance's control console, restoring a clean, finished appearance and securing the control interface. Fits as the visible console trim around buttons and display. What it does:

• Replaces a cracked, scratched, or warped control bezel to restore a neat front appearance
• Keeps control buttons and the display area properly aligned and protected
• Helps prevent dirt and moisture from reaching the underlying control components
• Can reduce button sticking caused by distorted or loose trim

• One control bezel (console trim)

• Disconnect power to the appliance before beginning any work
• Removal typically requires loosening console screws or clips; handle trim and clips gently to avoid breakage
• Keep all fasteners and note their original locations for reassembly

This air duct directs airflow inside the appliance to help maintain proper ventilation and cooling. Replacing a damaged duct restores correct air movement and can reduce noise or uneven temperature issues. What it does:

• Channels warm or cool air through the appliance's ventilation path
• Prevents air leaks that can cause unusual noises or reduced performance
• Helps maintain consistent internal temperatures and component cooling
• Supports connected seals and ducts to ensure efficient airflow

• Disconnect power before servicing to avoid shock or injury
• Inspect surrounding seals and fasteners; replace any that are worn or broken
• Handle carefully to avoid cracking plastic tabs during removal/installation

This switch actuator assembly transfers motion to a microswitch so the appliance can sense a required condition and operate safely. If the actuator wears or breaks, the switch may not engage, causing no-start or intermittent operation. What it does:

• Presses the corresponding microswitch at the correct point in the mechanism's travel
• Signals the control that a required condition is met
• Helps prevent operation when the mechanism isn't in the correct position
• Common symptoms of a failed actuator: won't start, starts and stops intermittently, or requires pressure on a handle/lever to run

• 1 switch actuator assembly

• Disconnect power to the appliance; if applicable, shut off gas
• Access the switch area; note the actuator's orientation before removal
• Transfer any screws/clips from the old part as needed; avoid bending the lever or over-tightening hardware
• After reassembly, test operation before fully closing panels

Replacement electronic control board that restores oven console functions and the control/display interface, helping return reliable timed cooking, temperature control, and user input response on compatible ovens and ranges. What it does:

• Powers and controls the oven's user interface and timed cooking functions.
• Manages temperature commands and cycles heating elements or igniters based on inputs.
• Common symptoms this replaces: blank or flickering display, unresponsive touchpad/buttons, or oven not starting/heating as expected.
• May clear control-related error codes when a failed board is the root cause.

• Disconnect power at the breaker or unplug the appliance before service to avoid shock.
• Handle the board carefully; avoid touching contacts and use antistatic precautions when possible.
• Some consoles require partial disassembly to access and swap the board; label or photograph connectors to ensure correct reassembly.

This genuine-style refrigerator door handle provides a secure grip for opening and closing the fridge while restoring a finished look. Durable replacement for a damaged, cracked or missing handle to help maintain normal door operation and appearance. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Restores proper pulling surface so the door opens and closes easily
• Helps keep the door sealed by enabling correct operation of the latch and hinge area
• Matches OEM fit and mounting points for a straightforward replacement

• Turn off power to the appliance or disconnect power supply before servicing
• Remove any trim or end caps to access mounting screws; a Phillips screwdriver or nut driver is commonly needed
• Handle screws may be hidden under cosmetic covers—retain all fasteners and trim pieces during disassembly

The Valve is an OEM part for Whirlpool dryers. It is responsible for controlling the flow of water into the dryer's steam generator, enabling the steam function during the drying cycle.

A bad steam water inlet valve can occur due to wear and tear, sediment buildup, or malfunctioning internal components. If you notice symptoms such as no steam being produced during the drying cycle, insufficient steam generation, or water leakage around the valve, it may be time to replace this part.

Symptoms of a bad valve include:

• No steam being produced during the drying cycle
• Insufficient steam generation
• Water leakage around the valve

Repair your dryer by replacing the faulty or damaged steam water inlet valve with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Console shell replaces the dryer's outer control housing to restore a clean, secure surface for the control assembly and controls. It repairs cosmetic damage while providing the proper mounting surface for the control components. What it does:

• Covers and protects the control assembly from impact, dust, and debris.
• Provides the structural mounting surface for knobs, switches and the control interface.
• Common symptoms it addresses: cracked, dented, warped or split console and loose or misaligned controls.
• Restores the dryer's appearance and helps prevent further damage to internal control components.

• Disconnect power (unplug the dryer or shut off the circuit breaker) before beginning any work.
• Removal/installation typically requires removing the dryer top or front panel; basic hand tools (screwdriver, nut driver) are commonly used.
• Handle any sharp sheet-metal edges with care and wear gloves and eye protection.

This wall elbow redirects the dryer vent through a wall opening, keeping the exhaust path secure and aligned for safe, efficient venting. Replaces a worn or damaged elbow to help restore proper airflow. What it does

• Provides a finished transition from the dryer vent pipe to the wall recess.
• Helps maintain a sealed vent path to reduce air leakage and lint buildup.
• Common fix for a cracked, loose, or broken elbow that causes noisy or inefficient venting.
• Works with standard dryer vent systems where a recessed wall box is used.

• Designed for use with compatible dryer vent housings;
• Turn off and disconnect the dryer before servicing; wear gloves to protect hands from sharp metal edges.
• Inspect surrounding venting and clear lint before final assembly to improve airflow and safety.