Wfw96heawo Parts

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This dispenser handle assembly replaces a broken, loose, or missing handle on your appliance's dispenser. It restores a solid grip and proper actuation so the dispenser opens or operates smoothly and looks clean again.

• Provides the user grip/actuator for the dispenser mechanism
• Enables smooth opening or activation of the dispenser
• Helps ensure consistent operation and a clean finished look
• Common symptoms: cracked or missing handle, loose/wobbly handle, hard-to-open dispenser, handle won't stay attached

• Disconnect power; if working near water lines, shut off the water supply
• Open access to the dispenser area; retain and reuse any mounting screws/clips
• Transfer any reusable trim or small parts from the old handle if applicable
• Align and secure the new handle; test operation before reassembly

Restore targeted spray in your dishwasher with this diverter valve assembly. It controls where wash water flows during the cycle, helping ensure both racks receive proper pressure for consistent cleaning performance.

• Directs wash water to selected spray arms/zones during the cycle
• Failure can cause poor cleaning or one rack not receiving spray
• Can lead to longer cycles or repeated wash segments as the control retries

• Disconnect power and shut off the water supply before servicing
• Access from the bottom of the dishwasher; remove toe-kick and pull unit out as needed
• Expect some residual water; use towels and wear cut-resistant gloves
• Ensure seals are properly seated, transfer any original clamps/fasteners as needed, and test for leaks after installation

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Keep your batch-feed disposer operating safely and easily. This actuator handle inserts into the sink opening to start and stop the disposer and also functions as the sink stopper on batch-feed models, replacing cracked, worn, or missing handles.

• Engages the internal switch to start/stop the disposer when inserted and rotated
• Provides a secure grip for controlled batch-feed operation
• Helps seal the drain to hold water in the sink between uses
• Symptoms include: disposer won't run or runs intermittently with the handle inserted, handle is cracked/loose, or won't lock/turn to engage

• Disconnect power to the disposer before testing or handling parts
• Ensure the sink opening and splash guard are clear so the handle seats fully
• Insert the handle into the drain, align/press down, and rotate per your owner's manual to engage; reverse to stop
• Never place hands inside the disposer; use tongs/pliers to remove objects

This door-mounted dispenser stores and releases detergent and rinse aid at the correct times during the cycle, helping restore consistent cleaning and drying results. Replace a worn or damaged unit to fix soap door and rinse aid issues.

• Holds detergent for the main wash and opens the cup during the programmed step
• Meters rinse aid into the final rinse to reduce spotting and improve drying
• Helps resolve symptoms like detergent left in the cup, soap door won't latch/open, leaking rinse aid, or poor cleaning performance
• Direct replacement for the original door dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire harness
• Release the retaining tabs/screws, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser flush, tighten mounting screws evenly, reconnect wiring, and run a test cycle to check for leaks and proper operation

Color: Grey

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Includes water temperature sensor.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual