Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't spin or agitate? This lid switch assembly detects if the lid is closed. Moderate DIY repair—front panel removal required. Video available.
Replaced lid switch assembly Read more
Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.
I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more
Hex head screws for securing panels and components in ranges and ovens. Replace missing, stripped, or corroded fasteners during repairs or reassembly.
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
Secures the timer dial to the shaft on top-load washers. Replace if the knob spins freely or won't engage properly. Confirm fit with your model.
I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.
Fix a washer that won't spin or agitates but doesn't spin properly. This mode shifter assembly switches between agitate and spin cycles. Advanced repair.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.
Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more
Hex head screw that secures the agitator coupler to the drive shaft in top-load washers. Replace if rusted, stripped, or missing to properly mount coupler.
My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
If water leaks into your washer drum when off or won't fill properly, the inlet valve may be faulty. Most DIYers complete this repair in 20-50 minutes.
I watched your video and I replaced the water inlet valve. The problem is now fixed. It took about 5 minutes to replace. I am a 60yr old woman and it was an easy fix. Read more
Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.
Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more
Suspension rod and spring assembly for washing machines. Installs between the tub and cabinet frame. Replace when cracked, broken, or worn to restore stability.
I shopped around a bit - found one retailer that only had 1 shock in stock, another that only stocked the front shocks, etc. There is definitely a difference in the springs between the green colored and white colored shocks! I've torn this washer down before, so I'm fairly familiar with how it's put together. I've seen some of the You-tube videos on replacing this item, and some of the videos show far more disassembly than is required. I only removed the front, top, and controls, and... Read more