Wm2688h Parts

Color: blue. Measures about 2-1/2 inches wide by 4-1/2 inches deep.

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This tub cover forms the front half of the washer's outer tub. It seals the tub and provides the mounting lip for the door boot, helping prevent leaks and keeping the spin basket properly aligned with the cabinet opening.

• Seals the front of the outer tub and provides a secure seat for the door boot/bellows
• Contains wash water during all cycles to prevent leaks and splashing
• Maintains proper clearance for the spin basket to avoid contact with the front opening
• Common failure symptoms include leaks at the front or bottom of the cabinet, visible cracks/warping, or the door boot repeatedly coming loose or tearing

• Disconnect power and water; wear gloves and protect sharp edges
• Remove top and front panels; release the outer boot clamp and peel the door boot from the front panel. Detach any hoses/wiring from the cover, remove the perimeter bolts, and transfer any fittings from the old cover
• Clean sealing surfaces; inspect/replace the tub-to-cover gasket if your model uses a separate one. Seat the new cover and tighten fasteners evenly in a crisscross pattern
• Reinstall the boot and clamp carefully, reassemble the cabinet, and run a fill/spin test to check for leaks

This door boot gasket seals the gap between the washer tub and front opening to keep wash water contained. Replace a torn, cracked, or deformed boot to stop front leaks and restore a reliable door seal.

• Creates a flexible, watertight seal between the outer tub and door opening
• Helps prevent water leakage from the front of the washer during cycles
• Common failure signs: visible tears or cracks, water on the floor near the door, door not sealing properly
• Wear, sharp objects, or overloading can damage the gasket over time

• Disconnect power and turn off water before servicing; wear gloves to protect hands from sharp cabinet edges
• Remove the outer spring clamp and peel the old boot from the front panel
• Access the inner clamp from inside the cabinet (front/top panel removal may be required); align index marks on the new boot and reconnect any small hoses/vents if present
• Seat the gasket evenly, reinstall both clamps, and run a short test to check for leaks

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

Locking pin for shock absorber.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This pump hose routes washer tub water to the drain pump, helping remove wash water during the drain cycle. Replace a cracked or clogged hose to stop leaks and restore normal draining. What it does:

• Channels tub water to the drain pump so the washer can expel water during drain/spin cycles.
• A worn or cracked hose can cause water leaks under the machine.
• Blocked or collapsed hoses can contribute to slow or incomplete draining.
• Compatible replacement for the OEM pump hose connection on qualifying LG washers.

• One pump hose (single hose as shown)

• Disconnect power and turn off water supply before beginning any repairs.
• Confirm correct routing and secure clamps when installing to prevent leaks.
• Inspect adjacent clamps and fittings for wear; replace if corroded or damaged.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair