Wm3499hva Parts

The Drain Hose Assembly is an OEM component specifically designed for LG washing machines. It safely directs contaminated water from the washing machine to a drain source such as a utility sink or standpipe.  

Causes of a faulty drain hose can include splits, cracks, clogs, or detachment from fittings due to wear over multiple machine cycles and years of use handling heated, soap-filled water.

Symptoms of a bad drain hose assembly include:

• Water leaks onto the floor during drain cycles  
• Clogs in the hose restricting drain flow
• Detachment from machine or drain outlet connection point

This OEM LG part is also compatible with select Sears/Kenmore models.

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.

• Couples with the stator to drive the inner tub during wash and spin
• Helps resolve no- or slow-spin complaints
• Can address a drum that won't turn or turns intermittently
• May reduce grinding/clicking from the rear caused by damaged rotor magnets

• Unplug the washer and turn off water supply before servicing
• Access from the rear; remove the center bolt and pull the rotor straight off the shaft
• Magnets are strong—keep fingers clear; align splines/keyway on reinstallation
• Tighten the center bolt securely and inspect the stator and sensor while open

Replacement control knob that restores smooth, reliable rotary control for front-panel selector shafts. Provides a positive grip and clear pointer for accurate selection so you can set temperatures, cycles, or power levels with confidence. What it does:

• Replaces a cracked, worn, broken or missing control knob so the selector turns and stays on the chosen setting
• Restores tactile grip and a visible pointer for precise adjustments
• Helps stop slipping, loose fit, or wobble felt when turning the control
• Works with the matching splined control shaft—does not modify electrical components

• Disconnect power to the appliance before replacing the knob to prevent accidental operation
• Pull the old knob straight off the control shaft; match the knob's spline/profile to the shaft and push the new knob fully onto the shaft until seated
• If the control shaft or retaining clip is damaged, replace the damaged component before installing the knob

This inlet hose carries water into the washer's fill system during wash and rinse cycles. Replacing a cracked or leaking hose restores proper filling and helps prevent water around the appliance from seepage at the connections.

• Routes incoming water to the washer's fill path during the fill cycle
• Helps maintain a watertight connection between the supply and the machine
• Replace if you see cracks, bulges, kinks, or active leaks
• Helps resolve water on the floor during fill, intermittent fill errors, or slow/no fill due to restricted flow

• Unplug the washer and turn off the water supply valves before starting
• Place a towel or pan to catch residual water and relieve line pressure
• Note hose routing/orientation; install the new hose without kinks and hand-tighten fittings
• Restore water and power, then check all connections for leaks during a short fill test

This pressure switch assembly monitors the washer's tub water level and signals the control to fill, drain, and advance cycles properly. Replacing a faulty switch restores accurate water level sensing for reliable washing performance.

• Senses air pressure from the tub to determine water level
• Helps prevent overfilling and underfilling
• Common failure symptoms: overfills or won't fill, won't advance to spin/drain, drains continuously, or shows a PE (water level sensor) error
• Can cause intermittent cycle stops when readings are inaccurate

• Disconnect power and turn off water supply before servicing
• Access is typically from the top/console area; note hose and connector positions
• Inspect/clear the pressure hose; ensure it's not cracked, kinked, or blocked
• Seat the hose fully on the barb and reconnect the wire harness securely; test a fill cycle for proper operation

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This stator assembly is the stationary motor coil that produces the magnetic field to drive the washer motor. Replaces a worn or damaged stator to restore magnetic coupling between the motor and rotor for normal drum movement. What it does:

• Generates the magnetic field the rotor uses to spin the drum
• Restores normal spin and agitation when a failed stator causes no-spin, weak spin, or humming
• Works with the washer's rotor/drive components as part of the motor assembly
• Handles the electrical and magnetic interface; must match motor/rotor configuration

• One stator assembly

• Disconnect power and water before servicing; use proper lockout procedures
• May require removal of the motor/rotor and housing to access the stator
• Inspect rotor magnets, bearings, and wiring for related damage while replacing

Direct-replacement display power control board assembly that restores power and control to the appliance's display and front control panel. Replaces a failed display module to get buttons, lights, and on-screen messages working again. What it does:

• Supplies power and control signals to the appliance display and front user interface.
• Restores responsive buttons, touch controls or soft keys when the display electronics fail.
• Stops or reduces display issues such as a blank, flickering, or dim screen.
• Helps address intermittent display behavior or loss of display backlight.

• Disconnect the appliance from power before starting work to avoid shock or short circuits.
• Handle the board by its edges and use ESD precautions (avoid static discharge) to protect electronic components.
• Keep track of screws and connectors; transfer any shields or mounting hardware from the old board if required.

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This DC fan motor assembly restores fan-driven airflow and circulation in compatible appliances, helping return normal cooling and ventilation performance. Use it to replace a failed or noisy fan motor for more reliable operation. What it does:

• Drives the appliance fan to maintain proper air circulation for cooling or ventilation.
• Replaces a motor that has stopped running, helping address reduced or no airflow.
• Can resolve loud, grinding, or rattling noises coming from the fan area.
• Help with inconsistent or warmer-than-normal temperatures caused by a failed fan.

• Disconnect power before starting — unplug the appliance or switch off the breaker.
• Photograph wiring and panel locations before removal to ensure correct reconnection.
• Handle sharp sheet metal and evaporator/coil areas with care; use gloves as needed.
• Verify the part number on your appliance and compare connectors and mounting before installation.

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.