Wmh164xws1 Parts

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This replacement screw is a general-purpose fastener used to secure exterior panels, trim, or internal components on compatible Whirlpool appliances. It restores proper fit and reduces rattles or loose parts for a safer, more reliable appliance. What it does:

• Secures panels, trim pieces, or mounting brackets to keep components in place
• Prevents vibration-related noise and movement caused by missing or loose fasteners
• Helps maintain alignment of control panels and exterior housings
• Replaces stripped, corroded, or lost screws to restore original fit

• Use the correct screwdriver or bit to avoid stripping the head
• Match screw length and thread engagement with the original for a secure fit
• Tighten to snug only; over-tightening can strip threads or crack panels
• Disconnect power before performing repairs on electrical components

The Fan Motor is an OEM part for Whirlpool microwaves. This fan motor is responsible for circulating air through the venting system. It works to evacuate fumes, smoke, and odors from the cooking area and direct them outside through the vent hood.

Causes of a bad fan motor can include excess dust or debris buildup hindering performance, bearing wear over time, or failure of electronic motor components.

Symptoms of a bad fan motor include:

• Inadequate or no air flow from the vent hood
• Strange noises coming from the vent system
• Reduced hood lighting levels
• Overheating or burning smells detected from the cooking surface or vent hood

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This wire harness assembly routes power and control signals between the appliance's main control and its components to restore reliable electrical connections. It replaces a damaged or intermittent wiring assembly to help components receive proper power and signals. What it does

• Connects the main control to heating elements, sensors, switches, or other components depending on appliance model
• Restores lost or intermittent power/signal paths caused by frayed, burned, or broken wires
• Helps resolve symptoms like components not powering, intermittent operation, or electrical arcing at connection points
• Maintains correct wire routing and connector fit for safe operation when installed properly

• Disconnect all power (unplug or switch off breaker) before beginning work
• Photograph existing routing and connector locations to ensure correct reinstallation
• Route harness without pinching; secure with original clips or ties and avoid heat sources

This replacement mounting plate secures internal components so the appliance operates quietly and stays aligned. Replacing a damaged or bent plate helps stop rattling, prevent part movement, and restore proper fit between adjoining parts. What it does:

• Provides a stable mounting surface for nearby components and fasteners
• Prevents parts from shifting or vibrating during operation
• Helps eliminate rattling or noise caused by a loose or bent plate
• Restores correct alignment where the original plate was damaged or deformed

• One replacement plate

• Disconnect power (unplug appliance or turn off circuit) before starting any repair
• Wear gloves and eye protection; edges may be sharp
• Use correct fasteners and torque to avoid bending the new plate;

Color: Universal Silver

This white microwave door replaces a damaged or worn outer door assembly to restore appearance and safe operation. It provides the exterior panel and handle mounting surface for a finished cabinet look. What it does:

• Replaces a cracked, dented or discolored outer microwave door panel
• Restores the cosmetic finish and proper door closure alignment
• Helps maintain the microwave's protective barrier during operation
• Works when the original door shell, trim or latch-mount area is damaged

• High-level replacement: remove microwave trim/outer screws and transfer any latch or trim pieces as required
• Handle and internal latch components may need to be transferred from the old door
• Disconnect power to the appliance before any service and follow OEM safety instructions

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed

A replacement plate used to secure or cover internal components and restore proper fit and protection for your appliance. This stamped metal plate helps keep parts aligned and shields wiring and openings from debris. What it does

• Secures or anchors nearby components to maintain correct alignment and operation
• Covers openings or service areas to protect wiring and insulation from debris
• Helps reduce vibration or rattling by providing a stable mounting surface
• Restores the original enclosure fit and appearance after part removal or repair

• One replacement plate as shown

• Disconnect power to the appliance before beginning any repair
• Installation requires basic hand tools; avoid overtightening fasteners
• Follow OEM instructions for correct placement
• If you encounter damaged fasteners, wiring, or mounting points, address those issues before completing installation