Wmh31017as-0 Parts

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This replacement door handle restores a secure grip and clean appearance to your refrigerator door. It matches the original mounting points for a direct-fit swap and helps you open and close the door smoothly. What it does:

• Provides a sturdy, ergonomic grip for opening and closing the refrigerator door
• Replaces damaged, cracked, or loose handles to restore safe operation
• Matches original mounting locations to maintain proper door alignment and function
• Designed for direct replacement without modifying the door

• One replacement refrigerator door handle

• Remove power to the appliance and empty door shelves before starting
• Typical install requires removing the door trim or screws at the handle mounting points
• Handle screws and any trim clips should be reused if undamaged; replace if stripped

This wire harness is the assembled wiring needed to replace a worn, damaged, or failed harness that connects appliance components and restores reliable power and signal paths. It helps return normal operation by replacing frayed or broken wires and connectors. What it does:

• Replaces the factory wiring assembly that links controls, switches, sensors and motors
• Restores electrical connections that can cause no-start, intermittent operation, or failed cycles
• Eliminates problems caused by loose, corroded, or damaged wires and terminals
• Prevents arcing or shorts from exposed or broken conductors when properly installed

• One complete wire harness assembly as shown

• Always disconnect power (unplug or shut off breaker) before servicing electrical components
• Verify routing and connector orientation match the original harness before securing
• Avoid stretching or pinching wires; secure with existing clips or fasteners
• If any connector or terminal appears damaged, replace the harness rather than attempt field repairs

Restore a solid, comfortable grip on your appliance door. This replacement door handle refreshes the look of your unit and makes opening and closing the door feel smooth and secure again. What it does:

• Provides the handhold needed to open and close the door
• Replaces a cracked, broken, or missing handle
• Helps correct a loose or wobbly handle
• Improves appearance when the original is scuffed or worn

• 1 door handle

• Disconnect power to the appliance before servicing
• Protect the door surface with tape or a cloth while working
• Use the correct driver (hex/Torx/Phillips) per your model to remove set screws or mounting screws
• Align the handle on the studs/mounts and tighten evenly without overtightening; verify smooth door operation

This replacement mounting plate secures internal components so the appliance operates quietly and stays aligned. Replacing a damaged or bent plate helps stop rattling, prevent part movement, and restore proper fit between adjoining parts. What it does:

• Provides a stable mounting surface for nearby components and fasteners
• Prevents parts from shifting or vibrating during operation
• Helps eliminate rattling or noise caused by a loose or bent plate
• Restores correct alignment where the original plate was damaged or deformed

• One replacement plate

• Disconnect power (unplug appliance or turn off circuit) before starting any repair
• Wear gloves and eye protection; edges may be sharp
• Use correct fasteners and torque to avoid bending the new plate;

This reflector directs and shields the oven light and surrounding area, helping maintain safe illumination and protecting the lamp from direct contact with food and heat. Fits behind the interior lamp in compatible ranges. What it does:

• Reflects and directs oven lamp light for improved interior visibility
• Shields the light from splatters and oven heat to protect the bulb assembly
• Helps maintain consistent light positioning after bulb changes or during cleaning
• Common symptom: dim or uneven oven lighting or a cracked/discolored reflector

• One reflector

• Disconnect power to the appliance and allow the oven to cool completely before starting
• Remove the oven light bulb and lens/cover to access the reflector
• Handle carefully to avoid bending or scratching; reassemble lamp components securely