Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a washer that won't spin or agitate. This motor capacitor stores energy to start and run the motor. DIY repair takes about 10 minutes with video help.
Washer would run through the cycle, but not agitate. I had to wait for it to pump down the water level to check spin, which also was not working. The motor would buzz when it should run, but not rotate, hard to hear for spin because the pump was running. Found I could start it by hand very easily by giving the pulley a spin, so I figured start switch, but there didn't appear to be one. I found what looked like a start capacitor zip tied to the chassis midway up the front, so my second guess was... Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Supports the washer tub and absorbs vibration during cycles. Replace if corroded, worn, or broken to prevent drum sagging and banging during operation.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
Suspension rod and spring assembly supports the washer tub and reduces vibrations. Replace if cracked, worn, or broken to restore proper tub support.
I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more
Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.
Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.
Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Replace your washer's damaged, rusted, or cracked lid assembly. Covers the drum to prevent splashing and ensure safe operation. Includes hinges.
Removing and Replacing (R&R) the parts took about 15 minutes. Getting the correct parts took several weeks. It was a severe struggle. Many of you will experience problems trying to get the correct "Lid" for similar GE washing machine models. AppliancePartsPros.com was great: Right price, Arrived quickly in good condition. I got the wrong part. It was not the fault of AppliancePartsPros.com, though. To make a long story short, GE has disseminated incorrect data in parts lists and it... Read more
Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.
My son fixed it Read more
Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.
Replaced lid switch and capacitor Read more
Baffle screw with flat washer for washers. Secures baffle or trim pieces to the washer body. Replace if screw is stripped, washer is missing, or worn.
Myself and help from friends. Read more
Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.
Pulled front panel off. Unbolted and removed top cover. Removed tub trim cover. Removed and replaced gasket and dampers. Put it a back together took about 20 minutes Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.