Wrt519szdw11 Parts

These inserts are for 1/4 inch plastic tubing. Package of 4.

This replacement gasket creates a tight seal between mating components in your appliance. Restoring a proper seal helps contain air or water where designed, improving performance and helping prevent leaks, moisture intrusion, and energy loss.

• Seals the interface between parts to prevent air or water escaping
• Helps maintain correct temperatures and fluid paths as designed
• Replaces a torn, cracked, flattened, or warped original gasket
• Common symptoms include leaks, visible gaps, or moisture around the sealed area

• Disconnect power and shut off water supply before service
• Note the original gasket's orientation; take photos for reference
• Clean and dry both sealing surfaces; remove old gasket material/residue
• Seat the new gasket fully and evenly; avoid over-tightening fasteners and test for a proper seal

Color: Grey

This small shim installs on the refrigerator's center hinge pin to set door height and reduce excess play. Replacing a worn spacer can help restore smooth door movement and a reliable gasket seal. What it does:

• Maintains proper spacing at the center hinge to support door alignment
• Reduces door wobble, sagging, or rubbing against the cabinet
• Helps doors open and close smoothly with consistent gasket contact
• Can lessen clicking or squeaking from a worn hinge interface

• Includes the center hinge spacer only

• Unplug the refrigerator or switch off power at the breaker
• Remove items from the door; support the door before loosening center hinge screws
• Lift the door off; place the new spacer on the center hinge pin in the same orientation as the original
• Reinstall the hinge and door; tighten fasteners and verify door alignment and gasket seal

This snap bushing installs in a door panel opening to protect and guide wiring or tubing that passes through. Replacing a worn or missing bushing helps prevent chafing and pinching, supporting smooth, reliable operation. What it does:

• Snaps into the door panel hole to create a smooth pass-through
• Shields wiring harness or tubing from sharp edges and vibration
• Helps prevent pinched wires, damaged insulation, or leaks due to abrasion
• Common signs include a cracked/missing bushing, chafed wiring/tubing at the door pass-through, or rubbing noises when opening/closing

• 1 snap bushing

• Disconnect power; shut off water supply if applicable
• Depress the old bushing's locking tabs and remove from the door panel opening
• Route the harness/tubing through the new bushing; align and press until it snaps fully into place
• Verify nothing is pinched and restore power/water

This replacement screw secures panels, brackets, or trim within your appliance. Replacing a worn, stripped, or missing screw restores a tight, rattle-free fit so components stay aligned and operate as intended. What it does:

• Fastens components at the original factory locations specified for this part
• Replaces missing, damaged, or stripped screws to restore holding power
• Helps reduce vibration and rattling from loose parts
• Maintains proper alignment of panels, covers, brackets, and trim

• Disconnect power (and gas, if applicable) before servicing
• Match to the original screw and install in the same location and orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver or nut-driver; transfer any washers or spacers from the original hardware if present

Replacement fan blade that moves air across the evaporator and through the cabinet to help maintain even temperatures. Restores proper airflow and reduces noise and vibration caused by cracked, bent, or worn blades. What it does:

• Circulates cold air from the evaporator throughout the refrigerator/freezer compartments
• Helps maintain consistent temperatures and reduce hot spots
• Reduces noise and vibration when replacing damaged or unbalanced blades
• Works with the evaporator/air-movement motor to support normal defrost and cooling cycles

• Disconnect power before accessing the evaporator/fan area to avoid electric shock.
• Remove shelves, panels, and the evaporator cover as needed to reach the fan assembly.
• Handle the blade carefully — edges and nearby sheet metal can be sharp.
• Inspect the fan motor shaft and mounting hardware; replace any worn or damaged components for best results.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

This burner orifice meters the gas delivered to a burner so you get a stable, properly sized flame. Replacing a clogged or damaged orifice helps restore quick ignition, consistent flame quality, and even heating on gas appliances.

• Meters gas flow from the valve to the burner for correct flame size and shape
• Helps maintain efficient, even heating and clean combustion
• Wear or blockage may show as delayed or no ignition, weak/uneven flame, or yellow tipping
• Can reduce popping or flare-ups caused by improper gas metering

• Shut off gas supply and disconnect power before servicing
• Remove the old orifice with the proper wrench/nut driver; install the new one snugly—do not overtighten
• After reassembly, leak-check connections and verify flame; adjust air shutter only if specified by the service manual

This leveler is the adjustable foot that threads into the base to stabilize and level the appliance. Proper leveling reduces rocking and vibration and helps doors, drawers, or tubs align and operate smoothly.

• Supports the appliance and allows height adjustment to compensate for uneven floors
• Helps prevent rocking, rattling, or excessive vibration during use
• Aids in proper door/lid alignment and smooth closing
• Replace if the foot is cracked, stripped, or missing

• Disconnect power; turn off gas or water supply if applicable
• With a helper, carefully tilt or raise the appliance and protect the floor
• Unthread the old leveler; hand-thread the new leveler to avoid cross-threading, then tighten as designed
• Adjust to level side-to-side and front-to-back; the unit sits stable on all corners

The Air Duct is an OEM part for Whirlpool refrigerators. It is a component that directs cool air throughout the appliance. The air duct is designed to channel air from the freezer section to the fresh food section.

Causes of a bad air duct can include cracks or fractures in the ducting material, damage to air vents or directional fins, or blockages that disrupt proper air flow.

Symptoms of a bad air duct include:

• Inconsistent or uneven interior temperatures
• Longer cool down times after door openings
• Frost or condensation issues in problem areas
• Portions of refrigerator not maintaining proper temperatures

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

A replacement hinge pin that secures and guides the appliance door hinge so the door opens, closes and stays aligned. Installs quickly to restore correct door pivot and reduce sag or binding. What it does

• Acts as the pivot point for the door hinge so the door swings smoothly.
• Restores proper door alignment to prevent gaps or doors that won't latch fully.
• Stops noisy or rough door movement caused by a worn or bent pin.
• Helps maintain seal performance by keeping the door flush with the cabinet.

• Disconnect power to the appliance and remove any items from the door area before starting.
• Support the door while removing/installing the pin to avoid damage or injury.
• Use appropriate hand tools and keep track of any retainers or fasteners removed.

Size: 8-18 x 1/2 inch.

Color: Black

The Handle is an OEM part for Whirlpool refrigerators. It provides the means to easily open and close refrigerator and freezer doors with an ergonomic grip.

Causes of a bad door handle can include cracks, breaks, or missing components that compromise secure closing of doors. Over time, handles can lose tension or experience wear to moving parts.

Symptoms of a failing door handle include:

• Difficulty opening or closing doors securely
• Excessive movement or wobbling of the handle
• Detached or missing handle components
• Inability to open doors fully without force

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This thimble provides a finished, secure collar for the dryer's exhaust opening, creating a proper connection point for the vent duct and helping reduce air leaks and lint escape at the wall or cabinet passthrough. What it does:

• Forms the transition between the dryer exhaust outlet and the wall or cabinet duct opening.
• Helps center and support the vent hose or duct so it seals more reliably.
• Reduces gaps that can cause lint accumulation or drafting around the vent opening.
• Common symptoms it can address: visible gap or torn duct at the wall, excessive lint around the vent opening, or poor airflow from a loose connection.

• Disconnect power to the dryer before servicing; for gas dryers, turn off gas supply and follow OEM safety steps.
• Pull the dryer away or remove the cabinet access as needed to reach the vent opening; handle lint carefully and clean the area before installing.
• Slide the thimble into the wall/cabinet opening and align the duct to seat against it; secure per OEM instructions and check for a snug fit and unobstructed airflow.
• Inspect and replace damaged ducting and fasteners; ensure proper clearance and re-check connections after a short test run.

This small fastener washer fits under a bolt or nut inside your washing machine, distributing clamping force and protecting surfaces. Replacing a worn or missing washer restores a secure fit and helps reduce vibration, rattling, and premature wear.

• Distributes load evenly under a bolt or nut to prevent damage and loosening
• Helps maintain correct spacing and alignment within the assembly
• Reduces metal-on-metal wear at the mounting point
• Can help address looseness, rattling/metallic noises, and excessive vibration

• Disconnect power and shut off water before servicing
• Note the original washer's position and orientation before removal
• Inspect the bolt/nut and mating surfaces; replace any damaged hardware
• Tighten to manufacturer guidance; avoid overtightening