Wtw5105hw0 Parts

The Motor-Drive is an OEM part for Whirlpool washing machines. It converts electrical energy into rotational motion to power the wash cycle. The motor transmits torque to the inner wash basket or tub through the drive system to clean clothes through agitation and spinning actions. Issues with the motor-drive can negatively impact the entire functionality of the washer.

Causes of failure can be wear and tear over time, damage from oversudsing or unbalanced loads, or exposure to moisture. Ensure your washer keeps running at its best with this OEM Whirlpool replacement part.

Symptoms of a bad Motor-Drive include:

• The washer failing to start or stopping mid-cycle
• Excessive noise or vibration coming from the motor area
• Slow or inefficient spinning
• Inability to advance through cycles

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

Color: Grey

The Lid Lock Bezel is an OEM replacement part for Whirlpool washing machines. 

Symptoms of a need to replace the bezel include:

• Cracks, discoloration, or visible damage to the bezel
• Looseness or detachment of the bezel from the panel

Causes of a damaged or worn bezel can include accidental impacts, exposure to cleaning chemicals, or general wear and tear over time.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This lid bumper cushions the top-load washer lid as it closes, reducing noise and preventing direct contact between the lid and cabinet. Replace a missing or worn bumper to help protect the lid finish and ensure a smoother close.

• Provides a soft stop at the lid's contact point to absorb impact
• Helps reduce closing noise and lid rattle
• Helps prevent scuffs or chips on the lid edge or cabinet top
• Common signs of failure: bumper missing, flattened, cracked, or louder slam when closing

• Disconnect power before servicing the appliance
• Open the lid and locate the factory bumper position(s) per your parts diagram
• Remove the old bumper and any debris; seat the new bumper firmly in the designated location
• Close the lid gently to verify proper contact and alignment

This is a range hood grease filter. It traps airborne grease and cooking residue so the blower and ductwork stay cleaner and the hood maintains proper airflow.

• Captures grease and particulates from cooking vapors to protect the fan and motor
• A clogged or damaged filter can cause reduced suction, noisy operation, or lingering cooking odors
• Replace if the mesh is clogged, warped, punctured, or if cleaning no longer restores airflow
• Helps maintain ventilation performance and reduce buildup inside the hood

• Disconnect power to the hood before servicing
• Allow the hood and filters to cool before handling
• Open the filter latch or tabs, remove the old filter, and seat the new filter with the tabs/latch aligned
• Restore power; check for proper airflow

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The washer pulley Cover is an OEM replacement part for Whirlpool washing machines. It is a removable plastic shroud that houses the drive pulley and belt mechanism.

Causes of a bad pulley cover can include cracks or breaks from repeated opening and closing over time. Chemical or moisture exposure can also damage plastic through standard usage cycles. 

Symptoms of a failing pulley cover include:

• Inability to properly close or latch the cover  
• Leaks or debris entering the pulley compartment
• Interference with belt or pulley movement
• Loose fasteners or mounting points that cause misalignment

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Grey

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.