Wtw8540bwo Parts

The Lid Hinge Arm is an OEM part for Whirlpool washing machines. This arm is a vital component of the washer's lid assembly, providing support and facilitating smooth opening and closing of the lid.

Common symptoms of a bad Lid Hinge Arm in a Whirlpool washing machine include:

• The lid not staying securely open or closed
• Difficulty in opening or closing the lid
• Misalignment or uneven movement of the lid

Causes of a bad Lid Hinge Arm can include:

• Normal wear and tear over time
• Physical damage or breakage
• Misuse or excessive force applied to the lid

If you notice any of the mentioned symptoms or suspect a faulty Lid Hinge Arm, replacing it can restore proper lid operation to your Whirlpool washing machine. This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub to Drain Pump Hose is an OEM replacement part for Whirlpool washers. This hose is responsible for transporting water from the wash tub to the drain pump during the drain cycle.

Causes relate to mineral deposits stiffening the interior over multiple years, natural cracking from repeated flexion, or punctures from foreign objects inside tub impacting the material.

Symptoms of a defective hose involve:

• Puddling or flooded pockets of water left inside tub after draining
• Slow or inefficient drainage taking excessive time
• Leaks from cracked tub connections or along hose itself

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This drain hose carries used water from your appliance to the home drain during and after the cycle. Replacing a damaged or clogged hose restores proper draining and helps prevent leaks and standing water.

• Routes wastewater from the appliance outlet to the household drain
• Maintains a sealed, unobstructed path for efficient draining
• Helps prevent leaks from splits, brittleness, or loose connections
• Commonly resolves slow/no drain, water left in the tub, or water backing up
• Visible kinks, cracks, or blockages in the hose indicate replacement is needed

• Disconnect power and shut off water supply before servicing
• Place a towel or shallow pan to catch residual water when removing the old hose
• Note original routing and clamp locations; avoid kinks or sharp bends during install
• Fully seat and tighten connections, then run a brief drain to check for leaks

This motor stator is the stationary windings for a direct-drive washer motor. Working with the rotor, it creates the magnetic field that turns the basket. Replacing a failed stator restores consistent wash and spin performance. What it does

• Provides the fixed windings for the direct-drive motor
• Works with the rotor to spin and tumble the basket
• Failure can cause no spin/tumble, intermittent movement, or loud humming
• May lead to motor/speed-related error codes and cycle shutdowns

• 1 motor stator assembly

• Disconnect power before servicing; allow moving parts to stop
• Access is typically from the rear; remove the rotor to expose the stator
• Handle the rotor's strong magnets carefully and keep metal objects clear
• Route and seat the wiring exactly as original; tighten mounting bolts evenly

The Washer Lid Screw is an OEM part for Whirlpool washing machines. This 6-32 x .340 screw secures the washer lid to the hinge assembly, ensuring the lid opens and closes smoothly and stays securely in place during operation.

Causes of a bad washer lid screw can include wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or mishandling. A compromised screw can lead to issues with the lid's stability and functionality.

Symptoms of a bad washer lid screw include:

• The washer lid feeling loose or wobbling
• Difficulty in opening or closing the lid
• Visible rust or corrosion on the screw
• The lid not staying securely in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.

Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.

Symptoms of bad washer fill hoses include:

• Leaks or puddles around the washing machine
• Reduced water flow into the washer
• Visible cracks or bulges in the hoses
• The washer taking longer than usual to fill with water

These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.

The Tub to Circulation Pump Hose is an OEM replacement part for Whirlpool washing machines. This hose provides a direct connection between the tub and circulation pump during wash cycles. The hose is responsible for transporting water from the tub to the circulation pump and spinning basket assembly.

Causes of a bad tub to circulation pump hose can include cracking, kinking or collapse of the inner lining. Wear and environmental factors like mineral buildup can weaken it over time.

Symptoms of a bad hose include:

• Water leaks within or around the washing machine
• The washer fails to fill or drain properly
• Reduced water pressure impacting cleaning performance

This genuine OEM Whirlpool part is compatible with brands like Maytag, KitchenAid, and more, it ensures long-lasting performance.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

Small but essential, this drain hose retainer is a clip that secures the hose in place during use or storage. It keeps the hose properly routed to help prevent kinks, pull-outs, and leaks. What it does:

• Holds the drain hose to the cabinet/frame for correct routing or stowage
• Helps prevent kinks, abrasion, and strain that can cause poor draining or leaks
• Replaces a broken, warped, or missing retainer so the hose stays put
• Common symptoms: hose won't stay clipped, falls during operation, visible damage, water near hose path

• 1 drain hose retainer

• Disconnect power and turn off the water supply before servicing
• Access the hose routing area and remove the damaged retainer
• Position and fasten the new retainer in the same location; route the hose through it
• Run a brief test to ensure secure routing and no leaks

Restore smooth ice and water dispensing with this refrigerator dispenser assembly in a stainless finish. It replaces the in-door dispenser module so a cracked housing or broken lever no longer hinders operation or appearance.

• Serves as the user-facing ice/water dispenser module mounted in the door
• Provides the paddle/actuator and support for the dispenser's components
• Helps resolve: broken or sticking lever, cracked/loose dispenser housing, nonresponsive dispenser when pressed, cosmetic damage to the dispenser area
• Direct, model-specific replacement; matches the stainless finish

• Disconnect power and shut off the water supply before servicing
• Carefully remove the dispenser trim/panel to avoid scratching the finish; retain screws and clips
• Transfer wiring connectors and any reusable parts from the original assembly per your model's parts list
• Restore power/water and test both ice and water dispensing; check for proper actuation and leaks

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection